background image

1.

Compression-type appliances 

which use 

flammable refrigerants 

shall be marked

with the symbol “Caution: risk of fire”. 

The height of the triangle in the symbol “Caution: risk of fire” shall be at least 15 mm. 

2.

 

– WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in

structure, clear of 

any 

obstruction. 

– WARNING: Do not use mechanical devices or other means to accelerate the defrosting

process, other than those recommended by the manufacturer. 

– WARNING: Do not damage the refrigerant circuit.

– WARNING: Do not use electrical appliances inside the food storage compartments of the

appliance, unless they are of the type recommended by the manufacturer. 

Do not store explosive substances such as aerosol cans with a flammable propellant in 

this appliance. 

3

.   

If the supply cord is damaged, it must be replaced by a special cord or assembly available 

from the manufacturer or its service agent. 

This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their safety. 

Children should be supervised to ensure that they do not play with the appliance. 

Caution

risk of fire

Summary of Contents for RIF123



















Reviews: