background image

 

European Safety Certificate   

Compliance Declaration 

 

The manufacturer assumes full responsibility for the compliance 

of products manufactured with relevant safety, health and 

environmental protection requirements set out in European 

Directives. Test reports are available for verification upon 

request. The manufacturer will present the quality certificate or 

manufacture license to a refrigerator dealer if so required.   

Furthermore, the manufacturer declares that all parts intended 

to be in contact with fresh food as described in this User’s 

Manual are free of toxic substances.   

                   

 

The symbol on the product or on i

t

packaging indicates that this product may 

not be treated as household was te. Instead 

it shall be handed over

 

to the applicable 

collection point for the  recycling of electrical 

and electronic equipm ent. By ensuring this 

product is disposed of correctly, you will 

help prevent potential n

e

g

a

tive 

consequences for the environment and   

 

 

human health, which could otherwise be

 

caused by  inappropriate waste handling of 

this product. For more detailed information 

about recycling of this product, please 

contact your local 

city

 office, your 

household waste dispos

a

l se

r

ice or the 

shop where you purchased the product.   

 

Summary of Contents for RIF89


















Reviews: