background image

CARBATEC.C OM.AU

31

DC-1200P

2 YEAR WARRANTY

WARRANTY

A.  We warrant that this Carbatec product will be free 

from defects caused by faulty workmanship or faulty 

materials for a period of 2 years from date of sale.

B.  This warranty is in addition to other rights and 

remedies you may have under a law in relation to the 

goods. 

C.  This warranty does not apply in any of the following 

cases:

i.  Defects arising from:

1.  fair wear and tear;
2.  corrosive atmosphere;
3.  damage or injury caused by deliberate act, 

lack of care or failure to comply with the 

recommended care and maintenance for the 

goods;

4.  improper use of the goods;
5.  alterations or repairs  

(not made by us) to the goods;

ii.  defects arising from an event outside of our 

control such as fire, flood, earthquake or other 

natural calamity, motor vehicle or other accident, 

strike, civil unrest, terrorism or war;

iii.  to accessory items such as after-market jigs, 

accessories or other items which are not sold or 

serviced by us and which are not sold with or were 

not included with the main unit purchased; or 

iv.  to wearable parts such as drive belts/shafts, 

bearings, bandsaw tyres, motor brushes, blades or 

abrasive belts/discs or other cutting or machining 

implements.

v.  damage caused to any electrical component, 

where connected to a power supply outside 

the country for which it was designed (namely 

Australia or New Zealand).

D.  If this warranty applies and you have complied with 

the procedure below for making a claim, we will, 

at our election, either repair the goods (or those 

parts of the goods recognised as defective) or will 

provide a replacement within a reasonable time at our 

expense.

E.  If this warranty applies, the procedure for  

making a claim is: 

i.  you must contact us by email; 

ii.  you must include in the email the following 

information:

1.  a copy of the order or receipt for the goods;
2.  the serial or batch number printed on the 

machinery manufacturing plate; and 

3.  a detailed description of the fault and how and 

when it arose; and 

4.  If the fault is a type covered by this warranty, 

we will then make arrangements with you for 

the return of the goods to us (for repair or 

replacement) at our cost using our transport 

providers or we may decide to attend at your 

premises to repair or replace the goods.

F.  Our liability (and that of our resellers) under this 

warranty is wholly limited to repair or replacement of 

the goods (or those parts of the goods recognised as 

defective) in accordance with the procedure above 

and you have no right to other compensation, costs 

or damages under this warranty. But this does not 

mean that you may not have other rights under a law 

in relation to the goods.

G.  If following our inspection of goods returned by you 

under this warranty it is found that this warranty 

does not apply and you are not otherwise entitled to 

repair or replacement by us, you must, if requested 

by us, reimburse our costs including parts, labour and 

freight.

H.  This warranty is not transferable and only the person 

who purchased the goods may make a claim.

Where the goods have been exported outside Australia 

or New Zealand, the Company may not require the 

Purchaser to return any allegedly faulty or defective 

Product for evaluation. However, the Company has the 

right to request the return for evaluation at purchasers 

cost.

STATUTORY NOTICE

Our goods come with guarantees that cannot be 

excluded under the Australian Consumer Law. You are 

entitled to a replacement or refund for a major failure and 

for compensation for any other reasonably foreseeable 

loss or damage. You are also entitled to have the goods 

repaired or replaced if the goods fail to be of acceptable 

quality and the failure does not amount to a major failure.

WARRANTY

Summary of Contents for DC-1200P

































Reviews: