Manual arming/disarming is controlling your security system via the remote transmitter. This security system
is equipped with an optional Automatic Arming feature which allows the security system to arm 45 seconds
after the last door is closed. Operation is as follows:
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 45 seconds. If you reopen any
protected Door, Hood orTrunk, the security system LED will stop flashing. It will begin flashing again once
the vehicle’s entrances are closed.
3. After the 45-second timer has elapsed, the security system will automatically “ARM”. The siren/horn will
chirp once, and the parking lights will flash once.
Automatic Arming with Automatic Door Locking (Programmable)
The vehicle doors will automatically lock after the automatic arming cycle has been completed.
Automatic Arming Bypass
While the system is in Disarmed Mode, press the button twice. The horn/siren will respond with one chirp
and the LED will turn “ON”. The security system will remain in this mode for as long as you wish. To exit this
mode press the or buttons and the system will return to normal status.
1. Press the button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now disarmed.
The vehicle door will unlock and the dome light will turn on for 30 seconds upon disarming if these items
are connected to the security system.
Tamper Disarming
If the security system had been previously triggered, upon disarm the siren will chirp 4 times and the parking
lights will flash 3 times.
Pathway Illumination
This optional feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10 seconds
upon the lock signal.
Two Step Door Unlock
This optional feature will unlock only the driver’s door upon disarming the security system. Pushing the
button a second time within 3 seconds will unlock the remianing doors.
Automatic Rearm
If this optional feature is selected, the security system will automatically rearm itself within 60 seconds
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened before the 60
second timer is up.
Manual Un-Lock / Disarm
Automatic Arming
5
The transmitter can be used as a remote panic switch to manually trigger the alarm system in case of an
emergency.
1. Press and hold the
button for 3 seconds to enter the Panic Mode (horn/siren will start to sound and
parking lights will flash).
2. While in Panic Mode the transmitter and buttons can be used to lock and unlock the door (if that
option is installed). However, if the button is pressed, the vehicle’s starter disable device (when
installed) will be disabled, allowing the vehicle to start.
3. To turn off the panic function, press and hold the
button again for 3 seconds or press and release the
or buttons.
4. If the panic function is not turned off by the transmitter, it will turn off and reset itself after 30 seconds.
Disarming without a Transmitter
Panic Feature
The override procedure may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).
2. Within 10 seconds push the valet switch. The alarm will stop sounding and enter disarm Mode. You can
now start and operate the vehicle normally.
6
Manual valet mode allows you to bypass all alarm functions eliminating the need to hand your transmitter
to parking attendants or garage mechanics. This mode is also a necessity if your transmitters become
in-operable. When the system is in Valet Mode, all alarm functions are off. However, the remote panic
feature and remote door locks remain operational. To enter the Manual Valet Mode, the system must first be
disarmed either by using your remote transmitter, or by operating the manual override sequence.
Enter Valet Mode
1. When in Disarmed Mode, turn the ignition to the “ON” position.
2. Push and hold the valet switch for 2 seconds. The LED will be on solid. Turn off the igntiion key and the
LED will flash every 5 seconds as long as the unit is in the Valet Mode.
Exit Valet Mode
1. To return to normal operation, turn “ON” ignition (LED will be on solid).
2. Push and hold valet switch for 2 seconds. The LED will be off, indicating
the system has now exited the Valet Mode.
Hold 2 Seconds
Manual Valet Mode
