Cardin Elettronica 305/GLi824, Instruction Manual

13

THE INTEGRATED CARDIN SYSTEMS ARE DESIGNED AND BUILT 

ONLY TO BE USED IN MADE TO MEASURE METALLIC STRUCTURES. 

CARDIN ELETTRONICA DO NOT GUARANTEE PRODUCTS THAT 

HAVE BEEN INSTALLED IN A WAY THAT DOES NOT CONFORM TO 

THE SUPPLIED INDICATIONS.
It therefore follows that the structure should be constructed in such a 

way as to guarantee the following characteristics:

•  Suitable for housing electronic appliances;

-  the upper part must be completely sealed, so as not to allow water 

infiltration (IP55);

-  Air vents should be fitted in both the upper and lower parts of the 

columns in order to avoid condensate build up;

•  Conformity with the dimensional and structural characteristics as stipu-

lated by good building practice;

•  The end structure should respect the parameters as laid down by the 

standards and regulations in force UNI EN 12453 with regard to main-

taining safety conditions during the use of motorized gates and doors.

•  These instructions are aimed at professionally qualified "

installers of electrical 

equipment

" and must respect the local standards and regulations in force. 

  All materials used must be approved and must suit the environment in which 

the installation is situated.

•  All maintenance operations must be carried out by professionally qualified 

technicians. 

  Before carrying out any cleaning or maintenance operations make sure the 

power is disconnected at the mains.

•  This appliance must be used exclusively for the purpose for which it has been 

made. "i.e. 

for the automation counterbalanced garage doors

"

•  Any unauthorised modifications are to be considered improper and therefore 

dangerous. 

•  The motor can be positioned either to the 

left

 or to the 

right

 of the installation. 

•  This appliance must never be used by people (including children) with physi-

cal, sensory or mental disabilities or by people without specific knowledge 

and experience in its operation unless they are able to benefit from the experi-

ence or are being taught to use the appliance whilst being safeguarded by the 

presence of somebody responsible for their safety. 

•  Before installing make sure that the guided parts are in good condition, cor-

rectly balanced and that they open and close correctly.

•  Avoid becoming trapped between the moving parts and the fixed parts during 

the opening and closing movements.

•  The motor’s power cable must be made of polychloroprene in conformity with 

the international standard 60245 IEC 57.

It is the responsibility of the installer to make sure that the following public safety 

conditions are satisfied:

It is the responsibility of the installer to make sure that the following public 

safety conditions are satisfied:
1)  The pedestrian door must not open on its own, e.g.; swing open while 

the garage door is in movement.

2)  The appliance must not be operated when the pedestrian door is not 

fully closed.

3)  Make sure that there are no dangerous sharp edges. 
4)  Make sure that the end-user is aware that children and/or pets must 

not be allowed to play within the area of a garage door installation. If 

possible include this in the warning signs.

5)  A correct earth connection is fundamental in order to guarantee the 

electrical safety of the machine.

6)  If you have any questions about the safety of the door operating system, 

do not install the operator. Contact your dealer for assistance. 

8) If you have any questions about the safety of the door operating system, do 

not install the operator. Contact your dealer for assistance.

TECHNICAL DESCRIPTION

•  The set consists of:
2  geared motors 

300/GLi824

 with an incorporated encoder without onboard 

electronics.

1  electronic programmer 

CCi924

 with NiMH batteries, a battery charger and an 

integrated S449 radio frequency module.

•  The geared motor is powered by 

24 Vdc

 and is fitted with a double-reduction 

kinetics system immersed in permanently fluid grease . 

•  The emergency manoeuvre is carried out by means of an efficient manual 

release system integrated into the geared motor.

•  The motor is connected to the electronic programmer by means of a 6 wire 

fast-fitting cable.

•  The electronic programmer is aimed at the management of 

24V

 encoder 

controlled motors for garage doors that allow door-positioning control. 

  Repositioning takes place automatically whenever foreign objects get in the 

way of the door as it is moving. 

  If the motor release system has been activated a sensor positioned on the 

mechanical components will force the programmer to carry out automatic 

repositioning the next time a command is given. 

  The electronic control unit is completed by the anti-crush and 

"soft start" and 

"soft stop"

 functions. 

  The electronic components are housed in a shock-proof plastic container 

IP55 and are factory fitted with a slot-in battery charger, NiMH buffer batteries 

driving the door during emergencies, an RF module for remote control and a 

Liquid Crystal Display

 (LCD 16 digits x 2 lines) which allows all the running 

functions and the number of manoeuvres carried out by the automation to be 

monitored as well permitting rapid parameter and function mode setting.

Attention!

 Only for EU customers - 

WEEE marking

.

This symbol indicates that once the products life-span has expired 

it must be disposed of separately from other rubbish. The user is 

therefore obliged to either take the product to a suitable differen-

tial collection site for electronic and electrical goods or to send 

it back to the manufacturer if the intention is to replace it with a 

new equivalent version of the same product.

Suitable differential collection, environmental friendly treatment and disposal 

contributes to avoiding negative effects on the ambient and consequently 

health as well as favouring the recycling of materials. Illicitly disposing of this 

product by the owner is punishable by law and will be dealt with according 

to the laws and standards of the individual member nation.

During the opening/closing manoeuvre check for correct operation and activate 

the emergency stop button in case of danger. 

During blackouts the garage door can be released and manually manoeuvred 

using the supplied release key (see manual release on pag. 14).

Periodically check the moving parts for wear and tear and grease if required using 

lubricants which maintain their friction levels unaltered throughout time and are 

suitable for temperatures of 

-20

 to 

+70°C

. 

In case of failure or operational anomalies switch off the power at the mains do 

not attempt to repair the appliance yourself. 

Periodically check the correct operation of all safety devices (photoelectric cells 

etc.). Eventual repair work must be carried out by specialised personnel using 

original spare parts. 

The appliance is not suitable for continuous operation and must be adjusted 

according to the model (see technical data on pag. 44). 

IMPORTANT REMARKS  

IMPORTANT REMARKS 

IMPORTANT REMARKS

READ THE FOLLOWING REMARKS CAREFULLY BEFORE PROCEEDING WITH THE INSTALLA-

TION. PAY PARTICULAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL 

NOT READING THESE IMPORTANT INSTRUCTIONS COULD COMPROMISE THE CORRECT WORK-

ING ORDER OF THE SYSTEM AND CREATE DANGER SITUATIONS FOR THE USERS OF THE SYSTEM.

IMPORTANT SAFETY INSTRUCTIONS

 USER INSTRUCTIONS