Cardin Elettronica 305/GLi824, Instruction Manual

16

“PROG/OK” to set

“PROG/OK” to confirm

BACK TO MOTION MENU

DIST. FROM OPEN

(5)

0...9 steps 

EXIT

OK

SEQUENTIAL COM. 

OPEN-SHUT/

OPEN-STOP-SHUT

“PROG/OK” to set

AUTO-RECLOSING

ON/OFF

“PROG/OK” to set

“PROG/OK” to set

WARNING LIGHTS

FIXED/

INTERMITTENT

“PROG/OK” to set

INDICATOR LIGHT

(1)

FIXED/

INTERMITTENT

“PROG/OK” to set

PHOTOCELL INVERT 

(2)

DURING CLOSING/

AND IN STOP

“PROG/OK” to set

“PROG/OK” to set

“PROG/OK” to set

“PROG/OK” to set

LC/CH2 OUTPUT

RADIO CHANNEL/

COURTESY LIGHT

“PROG/OK” to set

“PROG/OK” to confirm

BACK TO OPTIONS

PRE-FLASHING

ON/OFF

TEST FI 

(3)

ON/OFF

TEST FS 

(3)

ON/OFF

MEMO RADIO

ON/OFF

EXIT

OK

“PROG/OK” to set

FI CONTACT

NC/8K2

TB CONTACT

NC/8K2

“PROG/OK” to set

“PROG/OK” to set

“PROG/OK” to set

“PROG/OK” to confirm

BACK TO SAFETY DEVICES

FS CONTACT

NC/8K2

CP CONTACT

NC/8K2

EXIT

OK

“PROG/OK” to set

CURRENT SENSOR 

(4)

LEVELS 1...5

“PROG/OK” to set

“PROG/OK” to set

LIMITED OPENING

1...9 meters

“PROG/OK” to set

ADJUST CONTRAST

0...63

CONTRAST

OK

“PROG/OK” to confirm

“PROG/OK” to confirm

SAFETY DEVICES

OK

“PROG/OK” to confirm

CANCELLATION

OK

MEMORISE

OK

“PROG/OK” to confirm

“PROG/OK” to confirm

“PROG/OK” to confirm

“PROG/OK” to confirm

BACK TO RADIO CODES MENU

CLEAR ALL MEMORY

OK

CHANNEL FUNCTION

OK

EXIT

OK

“PROG/OK” to confirm

REMOTE

OK

OPTIONS

OK

“PROG/OK” to confirm

MOTION

OK

PRESS ANY KEY

BACK TO TEST MENU

“PROG/OK” to confirm

TEST

OK

“PROG/OK” to confirm

DISPLAY

OK

“PROG/OK” to confirm

“PROG/OK” to set

“PROG/OK” to confirm

BACK TO DISPLAY MENU

EXIT

OK

REAR LIGHTING

ALWAYS ON/

60 SEC./30 SEC.

TORQUE SELECTION

LEVELS 1...2

PROGRAM

T B

F S

F I

CP

00.000.001

T B

F S

F I

CP

TEST

T B

F S

F I

CP

“PROG/OK” to set

CHANNEL A

COMMAND TD/TAL/TA/TC/

STOP/CH2 OUTPUT/

NO COMMAND

CHANNEL B

COMMAND TD/TAL/TA/TC/

STOP/CH2 OUTPUT/

NO COMMAND

“PROG/OK” to set

“PROG/OK” to set

“PROG/OK” to set

“PROG/OK” to confirm

 BACK TO CHANNEL FUNCTION MENU

EXIT

OK

CHANNEL C

COMMAND TD/TAL/TA/TC/

STOP/CH2 OUTPUT/

NO COMMAND

CHANNEL D

COMMAND TD/TAL/TA/TC/

STOP/CH2 OUTPUT/

NO COMMAND

PRESS the 

transmitter 

channel to be 

memorised

CANCELLING.....

MEMORISE [nr ...]

Activation 1

PRESS the 

transmitter 

channel to be 

memorised

MEMORISE [nr ...]

Activation  2

MEMORISE [nr ...]

CODE MEMORISED

“PROG/OK” to confIrm

CLEAR ALL MEMORY?

OK

PRESS the 

transmitter 

channel to be 

cancelled

CANCEL [nr ...]

Activation 1

PRESS the 

transmitter 

channel to be 

cancelled

CANCEL [nr ...]

Activation  2

CANCEL [nr ...]

CODE CANCELLED

Exit

Notes

:

1)  The indicator light flashes slowly during opening, rapidly during closing; remains lit when the 

door is blocked but not completely closed and is off when the door is completely closed.

2) 

FI 

Mode:

- 

FI

 also active when the door is blocked: If the photocells are in alarm and the door is 

blocked, no movement commands will be accepted (even opening commands);

- 

FI

 active only during closing

  In both cases activating the 

FI

 safety device during the closing stage will force travel 

direction inversion.

3) Photocell test (

FI/FS

) 

  If you enable the security test you will have to connect both the transmitter and the receiver 

to the controlled load output (

CTRL 24 Vdc

). When the test is enabled one second will 

pass between receiving a command and carrying it out.

4) Current sensor settings:
- 

Level 1

 = motor electrical input + 

2

amps

- 

Level 2

 = motor electrical input + 

3

amps

- 

Level 3

 = motor electrical input + 

4

amps

- 

Level 4

 = motor electrical input + 

5

amps

- 

Level 5

 = motor electrical input + 

6

amps

The programmer checks the electrical input to the motor, detecting any eventual increase 

in effort above the normal operating limits and intervenes as an additional safety device. 
5) Setting the distance from the opening travel limit:
  To increase or reduce this distance modify the parameter in steps from 0 to 9 (range fro 

0 to 6 cm ~). By default the appliance is set to level 4 and in this way the door will not 

slam against the travel limit but will stop within a centimetre of it.

  PROGRAMMING PROCEDURE (parameter setting)

•  All the functions of the electronic programmer can be set in the Display menu "

LCD1

" using the three buttons contained therein:

-  use the arrows to navigate through the menu and/or to adjust the display contrast;

- use 

"PROG/OK"

 to modify the parameter settings and/or to confirm.