Cardin 100/SL324EBSB, Instruction Manual

14

s 4HESEINSTRUCTIONSAREAIMEDATPROFESSIONALLYQUALIlED

INSTALLERS OF ELEC-

TRICAL EQUIPMENT

ANDMUSTRESPECTTHELOCALSTANDARDSANDREGULATIONS

in force. All materials used must be approved and must suit the environment in 

which the installation is situated.

s !LL MAINTENANCE OPERATIONS MUST BE CARRIED OUT BY PROFESSIONALLY QUALIlED

technicians. 

s 4HISAPPLIANCEMUSTBEUSEDEXCLUSIVELYFORTHEPURPOSEFORWHICHITHASBEEN

MADE

i.e. for the automation of sliding gates

WITHAMAXIMUMWEIGHTOFUP

to 

3000 kg

.

s 4HEGEAREDMOTORCANBEPOSITIONEDEITHERTOTHE

left

 or to the 

right

 of the pas-

sageway. Any non authorised modifications are to be considered improper and 

therefore dangerous. 

Caution!

 The installation of both anti-derailment buffers 

is absolutely obligatory.

It is the responsibility of the installer to make sure that the following public safety 

conditions are satisfied:

1) Ensure that the gate operating installation is far enough away from the main 

road to eliminate possible traffic disruptions and that the size of the gate, the 

distance from the road and the work cycle speed can in no way interfere, causing 

possible traffic hazards.

2) The motor must be installed on the inside of the property and not on the public 

side of the gate. The gates must not open onto a public area.

3) The gate operator is designed for use on gates through which vehicles are pass-

ing. Pedestrians should use a separate entrance.

4) The minimum controls which may be installed are OPEN-STOP-CLOSE, these 

controls must be installed at a height between 

1,5 

and 

1,8 m

 and in a location 

not accessible to children. Controls installed externally must be protected by a 

safety device inhibiting unauthorised use.

5) The gate must be in full view when it is operating therefore controls must be 

situated in a position where the operator can see the gate at all times.

6)

 At least two warning signs

 (similar to the example on the right) should be placed, 

where they can be easily seen by the public, in the area of the 

system of automatic operation. One inside the property and one 

on the public side of the installation. These signs must be indelible 

and not hidden by any objects (such as tree branches, decorative 

fencing etc.). Make sure that the end-user is aware that children 

and/or pets must not be allowed to play within the area of a gate 

installation. If possible include this in the warning signs

7) A correct earth connection is fundamental in order to guarantee 

the electrical safety of the machine

8) Before carrying out any cleaning or maintenance operations make sure the power 

is disconnected at the mains, the motor power cables are disconnected and the 

batteries have been disconnected. 

9) If you have any questions about the safety of the gate operating system, do not 

install the operator. Contact your dealer for assistance. 

TECHNICAL DESCRIPTION

-  Mains power supply 

230 Vac

.

-

Motor powered with a maximum voltage of 

35 Vdc

.

-  Upper cover in highly resistant shock-proof plastic.

-  Integrated  lower  cover  in  die  cast  aluminium  containing  a  never  ending 

screw and double reduction lubricated with permanently fluid grease.

-  Irreversible reduction system with a key operated manual release mechanism.

-  The incorporated electronic programmer contains the power stage, the logic 

control, battery charger and the radio receiver decoding module. The power 

supply is routed to the electronics card via a separate transformer which is 

housed in the same container and is connected to the card by Faston clips.

-  The system is fitted with electronic deceleration control which reduces the 

stress caused by the gate inertia when it stops.

Accessories 

106/CRENY

  -  Rack (

20 mm x 30 mm

) in glass fibre with upper  

  fastening slits (

1 m

). 

106/CRENY1

  -  Rack (

20 mm x 30 mm

) in glass fibre with lower  

  fastening slits (

1 m

). 

106/SLOAC

  -  Rack in galvanised steel (

22 mm x 22 mm

) 

2 m

 to be welded.

106/SLOAC2

  -  Rack in galvanised steel (

12 mm x 30 mm

)

1 m

 with fastening slits.

950/XLBS

-  Contact safety edge available in lengths of:

1,5

 and 

3,0 m

 maximum height 

70 mm

.

Attention!

 Only for EU customers - 

WEEE marking

.

This symbol indicates that once the products life-span has expired 

it must be disposed of separately from other rubbish. The user is 

therefore obliged to either take the product to a suitable differen-

tial collection site for electronic and electrical goods or to send 

it back to the manufacturer if the intention is to replace it with a 

new equivalent version of the same product.

Suitable differential collection, environmental friendly treatment and disposal 

contributes to avoiding negative effects on the ambient and consequently 

health as well as favouring the recycling of materials.

Illicitly disposing of this product by the owner is punishable by law and will 

be dealt with according to the laws and standards of the individual member 

nation.

During the opening/closing manoeuvre check for correct operation and activate 

the emergency stop button in case of danger.
During blackouts with a flat battery the gate can be released and manually 

manoeuvred using the supplied release key (see manual release fig. 8). 
Periodically check the moving parts for wear and tear and grease if required, 

using lubricants which maintain their friction levels unaltered throughout time 

and are suitable for temperatures of 

-20 to +70°C

. 

Eventual  repair  work  must  be  carried  out  by  specialised  personnel  using 

original spare parts. 
The appliance is not suitable for continuous operation and may only be oper-

ated using a duty cycle of 

70%

. 

Before starting the installation make sure that the structure which is to be 

automated is in good working order and respects the local standards and 

regulations in force. To this end ensure that:

 4HESURFACEOFTHESLIDINGGATE

A

ISSMOOTHANDHASNOPROTRUSIONSUPTO

a distance of 

2.5 m

 from ground level. 

  Protrusions on the gate surface which are not greater than 

3 mm

 and have 

rounded edges are acceptable. 

  If the surface of the gate is not smooth, the entire height up to 

2.5 m

 from 

the ground must be protected by two of the following devices:

a) photoelectric cells
b) contact safety buffer

 THEDISTANCE

B

BETWEENTHElXEDPARTSANDSLIDINGPARTSOFTHEINSTALLATION

must not exceed 

15 mm

.

 THE RUNNER GUIDE 

C

 PREFERABLY ROUND SHOULD BE SECURELY lXED TO THE

ground,  completely  exposed  and  free  of  any  imperfections  which  could 

inhibit the correct movement of the gate.

-  when the gate is closed a space of 

50 mm

D

MUSTREMAINFORTHEENTIRE

HEIGHTOFTHEFRONTPARTOFTHEGATEANDAMECHANICALTRAVELLIMIT

E

MUST

be positioned on the upper part of the gate.

 4HEFREESPACE

D

CANBECOVEREDWITHARUBBERANTICRUSHBUFFER

F

OR

better still a pneumatic or photoelectric contact safety buffer.

 IFTHEGATESLIDESPASTAlXEDSTRUCTURE

G

WHICHHASRAILINGSORBARSLEAVING

open spaces, it must be protected in one of the following ways:

DISTANCE

H

GREATERTHAN

500 mm

: no protection required;

DISTANCE

H

BETWEEN

500

 and 

300 mm

WIREMESHFENCING

I

ORPUNCHED

METALPLATING

L

WITHANOPENINGWHICHDOESNOTALLOWTHEPASSAGEOFA

25 mm

DIAMETERSPHERE

M

MUSTBElTTED

DISTANCE

H

SMALLERTHAN

300 mm

WIREMESHFENCING

I

ORPUNCHEDMETAL

PLATING

L

WITHANOPENINGWHICHDOESNOTALLOWTHEPASSAGEOFA

12 mm 

DIAMETERSPHERE

M

MUSTBElTTED

 4HEWIRESOFTHEMESH

I

MUSTNOTHAVEACROSSSECTIONOFLESSTHAN

2.5 mm

2

ANDTHEPUNCHEDMETALPLATING

L

MUSTNOTHAVEATHICKNESSOFLESSTHAN

1.2 mm

0ROTECTIONISNOTNECESSARYFORTHEAREA

P

IFTHElXEDSTRUCTURE

with railings or bars is over 

2.5 m

 above the ground. 

  IMPORTANT REMARKS 

IMPORTANT REMARKS 

IMPORTANT REMARKS 

IMPORTANT SAFETY INSTRUCTIONS

Q

AUTOMATIC OPENING

KEEP CLEAR

CHILDREN OR PETS MUST NOT 

BE ALLOWED TO PLAY ON OR 

NEAR THE INSTALLATION

WARNING

PRELIMINARY CHECKS (fig. 1, pag. 2)

READ  THE  FOLLOWING  REMARKS  CAREFULLY  BEFORE  PROCEEDING  WITH  THE  INSTALLATION.  PAY  PARTICU-

LAR ATTENTION TO ALL THE PARAGRAPHS MARKED WITH THE SYMBOL 

. NOT READING THESE IMPORTANT 

INSTRUCTIONS COULD COMPROMISE THE CORRECT WORKING ORDER OF THE SYSTEM AND CREATE DANGER 

SITUATIONS FOR THE USERS OF THE SYSTEM.

 USER INSTRUCTIONS