Cardin 100/SL324EBSB, Instruction Manual

18

s #AUTION

 The installation of both anti-derailment buffers is absolutely 

obligatory 

before starting programming.

s -AKESURETHATTHESAFETYDEVICESAREATRESTANDTHE%#5ISRECEIVINGMAINSPOWEROTHERWISEYOUWILLNOTBEABLETOENTER

  programming. 

PROGRAMMING PROCEDURE (Setting the programmer and the current sensor)

Dip-switch settings DS1

Sequential command TD/CH1

$IP/.  3EQUENTIALCOMMANDOPENCLOSE

Travel direction inversion only during closing.

$IP/&& 3EQUENTIALCOMMANDOPENBLOCKCLOSEBLOCK

Automatic reclosing (DIP 2)

$IP/.  !UTOMATICRECLOSINGENABLED
$IP/&& !UTOMATICRECLOSINGDISABLED

Pre-flashing (DIP 3)

$IP/.  0REmASHINGACTIVATED
$IP/&& 0REmASHINGEXCLUDED

Warning light output (DIP 4)

$IP/.  7ARNINGLIGHTOUTPUTINTERMITTENT
$IP/&& 7ARNINGLIGHTOUTPUTlXED

Indicator light (DIP 5)

$IP/.  )NDICATORLIGHTINTERMITTENT

*

$IP/&& )NDICATORLIGHTlXED

* 

The  indicator  light  flashes  slowly  during  opening,  rapidly  during  closing; 

remains lit when the gate is blocked but not completely closed

and is off when 

the gate is completely closed.

FTCI (DIP 6)

$IP/. 

FTCI

 also active when the gate is blocked

If the photocells are in alarm and the gate is blocked, no movement commands 

will be accepted (even opening commands).

$IP/&&

FTCI

 active only during closing

In both cases activating the 

FTCI

 safety device during the closing stage will 

force travel direction inversion.

FTCI test (DIP 7)

$IP/.  

FTCI

 test enabled

$IP/&&

FTCI

 test disabled

If you enable the security test you will have to connect both the transmitter and 

the receiver to the controlled load output (

CTRL

30 Vdc

).

When the test is enable one second will pass between receiving a command 

and carrying it out. 

Motor installation (DIP 8)

$IP/.  2IGHTHANDMOTORINSTALLATION
$IP/&& ,EFTHANDMOTORINSTALLATION

Manual operating mode (DIP 9)

$IP/.  -ANUALMODEENABLED
$IP/&&  -ANUALMODEDISABLED

Caution:

 If the symbol 

 appears on the display 

after  3  minutes  has  passed  since  the  program-

mer  was  powered  up,  the  gate  will  start  moving 

automatically (after the warning lights have flashed 

for 10 seconds) to the completely closed position 

(automatic repositioning). 

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

1 2 3 4 5 6 7 8 9

ON

WHEN THE GATE REACHES THE COMPLETELY CLOSED POSITION IT INVERTS THE TRAVEL 

DIRECTION AND AFTER MOVING FOR A FEW CENTIMETRES IT WILL CLOSE AGAIN TO 

CONFIRM THE COMPLETELY CLOSED POSITION. AT THIS POINT THE OPENING MANOEUVRE 

WILL START, AT LOW SPEED, SO AS TO FIND THE COMPLETELY OPEN POSITION. THEN IT WILL 

OPEN AND CLOSE AGAIN STOPPING THE GATE NEAR THE END TRAVEL LIMIT SO AS TO 

MEASURE THE CLOSING INERZIA. AT THIS POINT THE OPENING MANOEUVRE WILL START, AT 

LOW SPEED, SO AS TO FIND THE COMPLETELY OPEN POSITION. ONCE IT HAS ARRIVED AT 

THE COMPLETELY OPEN POSITION, IT INVERTS THE TRAVEL DIRECTION FOR A FEW 

CENTIMETRES AND THEN CONTINUES OPENING IN ORDER TO CONFIRM THE  COMPLETELY 

OPEN POSITION. IT WILL NOW CLOSE AND OPEN AGAIN STOPPING THE GATE NEAR THE END 

TRAVEL LIMIT SO AS TO MEASURE THE CLOSING INERZIA.

AFTER HAVING CARRIED OUT THIS MANOEUVRE THE GATE WILL CLOSE AGAIN.  ONCE IT HAS 

REACHED THE COMPLETELY CLOSED  (2-3 CM FROM THE MECHANICAL TRAVEL BUFFER) THE 

CONTROL LOGIC WILL CARRY OUT A COMPLETE OPENING AND CLOSING CYCLE IN ORDER TO 

CALIBRATE THE CURRENT SENSOR. 

WHEN THE GATE REACHES THE 

COMPLETELY CLOSED POSITION THE 

PROGRAMMER SAVES THE PARAMETERS 

AND QUITS THE PROGRAMMING MODE

THE OPERATION HAS NOT 

SUCCEEDED. YOU WILL HAVE 

TO REPEAT THE 

PROGRAMMING PROCEDURE.

PRESS THE 

PROG

 BUTTON FOR MORE 

THAN 4 SECONDS: THE 

PAUSE

39-"/,

WILL APPEAR INDICATING THAT YOU ARE 

IN THE PAUSE PROGRAMMING MODE

1...4... sec.

PRESS PROG

THE PAUSE TIME COUNT 

ENDS AND THE GATE CLOSES 

SLOWLY IN ORDER TO FIND 

THE COMPLETELY CLOSED 

POSITION. 

THE PAUSE TIME COUNT 

WILL START INDICATED BY 

THE 

PAUSE

39-"/,

FLASHING ON THE DISPLAY 

PRESS PROG

ATTENTION! IF THE GATE MOVES 

IN THE OPENING DIRECTION DIP 

8 HAS BEEN SET INCORRECTLY. 

PRESS 

PROG

/2

TB

!'!).

TO CANCEL THE PROCEDURE , 

SET DIP 8 CORRECTLY AND 

REPEAT THE PROGRAMMING 

PROCEDURE.

ATTENTION! 

If you change the dip settings during normal operation you 

WILL HAVE TO MEMORISE THEM 7HEN THE DISPLAY IS OFF PRESS THE 

PROG

BUTTONONCE4HESYMBOLDI0WILLAPPEARONTHEDISPLAYCONlRMINGCORRECT

memorisation. 

CURRENT SENSOR

The  programmer  checks  the  electrical  input  to  the  motor,  detecting  any 

eventual increase in effort above the normal operating limits and intervenes 

as an additional safety device. 

When the sensor intervenes the gate will automatically invert for 

10 cm

, both 

in the closing as well as the opening direction, to free the obstacle it will then 

stop for 

3 minutes

 and then continue moving in the original direction after a 

10 second

 preflashing period has elapsed.