background image

 

HF3000-Series Installation Manual

 

Doc. No. Revision 

07-0002 Rev.3 

Page 

3

 of 

14

 

 

 

 

© 2018 Cardinal Health. All Rights Reserved. CARDINAL HEALTH, the Cardinal Health LOGO and ESSENTIAL TO CARE are trademarks or registered 

trademarks of Cardinal Health. All other marks are the property of their respective owners.

  

5

 

RESPONSIBILITY 

 

Activity 

Responsible Party 

Shipping  

WaveMark 

Receiving 

Customer 

Unpacking 

Customer 

Moving Cabinet and Shelves from Receiving to Department 

Customer 

Training on shelf installation and shelf movement 

WaveMark 

Shelf Installation 

Customer 

Placing Inventory on shelves 

Customer 

Connecting cabinet to power and Ethernet 

Customer 

Installing wall bracket 

Customer 

 

6

 

WORK SAFETY 

 

I

t is our highest priority that all field installations comply with the company’s installation and safety 

procedures and any safety procedures in place at the location of installation. 

 

In order to assure that  equipment  is installed in  a safe manner and in  compliance 
with  installation  guidelines  only  trained  personnel  are  authorized  to  activate  or 
service cabinets.  This product contains no user-serviceable components. 

 

 

 

Summary of Contents for WaveMark HF3000 Series















Reviews: