background image

DRAFT 

 

 

  Page 5 of 19 

3.1 

Charging Battery 

Make sure the headset is fully charged prior to initial use. Allow at 

least 

Four

 hours for a full charge before using for the first time. Normally 2-3 hours 

will suffice for complete charge. The headset should be off the helmet when being 
charged (solely for purposes of convenience) 

  Plug the Wall Charger into the charging socket of the headset and connect it to an 

electrical outlet. 

  The Red Light Indicator (LED) on the scala-rider will turn on when charging begins. 

Allow the headset to charge until the Red LED turns off. 

  When charging is complete, release the headset from the charger.  

NOTE: You may leave the unit connected even if charging is completed. There is no 
danger of over-charging.

 

 

3.2 

Attaching and removing the scala-rider from your helmet  

4.2.1  First installation 

Once the headset is fully charged you should 

pair 

it to your mobile 

phone. 

You cannot operate the headset prior to successful pairing

 

(see section 5 below). When done, proceed with attaching the unit to your helmet 
as follows: 

 

 

 

 

 

 

 

 

back plate

  

  The clamp serves as the base for the headset and must be attached to your 

helmet before using the headset  

  Use the enclosed Allen Wrench to loosen the two 

screws of the clamp (FIG. 1). Then slide the back-
plate of the clamp between the internal padding and 
the external shell of the helmet (FIG. 2).  
(In case the external shell of the helmet is too wide, 
use the optional extension pad)  

  Before fastening the screws, make sure to adjust the 

clamp’s location to an ideal position, i.e. to the spot 
where the attached speaker sits opposite your ear 
and the microphone is located slightly off the

 corner 

of your mouth (FIG. 3). You may need to re-position 
the clamp repeatedly until you identify the ideal spot.  
The speaker can be easily placed into position and 
removed by means of the Velcro layer that  

     attaches to the inner padding of your helmet. 
     (Velcro pad included in your retail box). 

  Once you have identified the ideal position for  

The microphone and speaker, use the Allen  

     Wrench to fasten the clamp.  
 

  Now slide the scala-rider headset downwards along the Sliding-Panel of the 

clamp (FIG. 4) until a light clicking sound indicates that the  

     headset has reached its proper operational position. 

  Turn on the headset by pressing and holding CTRL for at least 6 seconds 

until the Blue LED flashes three times and an ascending alert tone is heard. 

FIG 2 

FIG 1 

Microphone should be placed  just slightly off 
the corner of your mouth

 and not at the center 

FIG 3 

Summary of Contents for ScalaRider




















Reviews: