background image

C

AREFREE OF 

C

OLORADO

 

S

UNDIAL 

P

ATIO 

A

WNING W

/

 

M

ANUAL 

O

VERRIDE

 

 12 

052537-001r5 

Extend

Retract

SunDay016

O

PERATION

 

S

WITCH 

O

PERATION 

 

S

TANDARD 

H

ARDWIRE 

I

NSTALLATION

 

  Press and hold the switch down to extend the awning to the desired extension. 

  Press and hold the switch up to retract the awning. 

 

 

 

 

 

U

SING THE 

W

IRELESS 

I

NTERIOR 

S

WITCH

 

STOP

STOP

SET

Single Channel

Switch

Multiple Channel

Switch

UP

STOP

DOWN

UP
STOP

DOWN

Channel Selector

Channel Indicator LEDs

Sunday019

 

Figure 14.  Wireless Switch. 

UP ......................... Press  and release the UP arrow to retract the awning.  The awning will retract until fully 

closed. 

STOP .................... Press the center button to stop the awning during extend or retract functions. 

DOWN................... Press and release the DOWN arrow to extend the awning.  The awning will extend to 

the maximum extension. 

Channel Selector .. For multiple channel switches:  Press the "Channel Selector" until the corresponding 

selection indicator LED is illuminated for the awning to be operated. 

When all 4 indicator LEDs are illuminated the remote is in "Group" mode.  All awnings 
will respond to the command buttons as a group (i.e. pressing the DOWN button will 
cause all awnings to extend). 

The wireless switch uses a flat 3V Lithium Battery (CR2430) that should provide a long period of service.  To 
replace:  Remove the switch from the wall mount.  On the back remove the box (2 screws).  Slide the old battery 
from the battery holder and slide a new battery in.  Pay attention to the polarity of the battery.  Batteries are 
available through local battery outlets. 

Table of Contents

Summary of Contents for SUNDIAL PATIO AWNING





















Reviews: