background image

070005-001r12 

Printed in USA 

May, 2019 

 

I

NSTALLATION 

M

ANUAL

 

L

ATITUDE

12V

 

M

OTORIZED 

L

ATERAL 

A

RM 

A

WNING

RV

 

 

Read this manual before installing or using this product.  Failure to follow the instructions 
and safety precautions in this manual can result in personal injury and/or cause the 
product to not operate properly. 

 

T

ABLE OF 

C

ONTENTS

 

Product Overview .......................................................................................................................... 1

 

Component Checklist.............................................................................................................................. 1

 

Installation ..................................................................................................................................... 2

 

Pre-Installation Requirements ................................................................................................................ 2

 

Mounting the Awning .............................................................................................................................. 2

 

Attaching the Canopy ..................................................................................................................... 3

 

Secure the Awning ......................................................................................................................... 3

 

Remove the Temporary Assembly Pins ......................................................................................... 3

 

Adjusting the Arm Position ............................................................................................................. 4

 

Jumping the Motor (when Direct Response is Installed) ........................................................................ 4

 

Jumping the Motor (without Direct Response) ........................................................................................ 4

 

Adjusting the Pitch .................................................................................................................................. 5

 

Switch Installation ......................................................................................................................... 7

 

Wiring Diagram - LCDR .......................................................................................................................... 8

 

LED Lighting .................................................................................................................................. 9

 

Switch Installation ................................................................................................................................... 9

 

 

Summary of Contents for LATITUDE












Reviews: