background image

Carefree Installation 

Manual  L

ATITUDE

 

070005-001r12 

P

RODUCT 

O

VERVIEW

 

The Latitude Awning is a state of the art lateral arm awning.  Each unit is equipped with lateral support arms.  No 
vertical arms interfere with coach sidewalls, custom graphics or equipment mounted on the sidewalls. 

  Fully retractable and self-storing; 

  Available in two configurations: single stage or dual stage; 

  The awning motor operates on standard 12VDC (range 10VDC to 14VDC); 

  Single touch operation for extend and retract; 

  LED lights standard, mounted in roller tube. 

S

PECIFICATIONS

 

Length 

Single Stage  10' 4" – 20' [3.15m – 6.1m] 

 

Dual Stage 

10' 4" – 18' [3.15m – 5.49m] 

Support: 

Lateral Spring Arms  

 

Motor: 

Power: 10VDC–14VDC 

Circuit Rating: 15 amp 

(motor is mounted in RH roller tube head) 

Power Source: 

Motor and controls are routed and hardwired into the vehicle’s 12V system 

Controls: 

Carefree Direct Response (to be phased out in 2019) 
BT12 Wireless Awning Control System 

Color: 

Hardware: 

White or Black 

 

Fabric: 

Heavy Duty Vinyl with Weatherguard or FLXguard 
(refer to sales literature for colors) 

Weight: 

 

10' 

4" 

12' 14' 16' 18' 20' 

 

Single Stage 

45.5 lbs. 

48.3 lbs. 

51.7 lbs. 

55.0 lbs. 

58.3 lbs. 

61.6 lbs. 

 

Dual Stage 

52.1 lbs. 

55.9 lbs. 

60.4 lbs. 

65.0 lbs. 

69.6 lbs. 

n/a 

C

OMPONENT 

C

HECKLIST

 

 

  I

TEM

 D

ESCRIPTION

 

Q

TY

  N

OTE

 

Awning Assembly 

 

 

QuicKonnect 

1  

 

Canopy Funnel 

 

 

Clamp, Cable 

1  

 

Screw, PPH 

#8 x 1"

 

 

Screw, HWHC 

#6 x 3/8"

 

 

Switch Kit, Direct Response 

 

Covered Bezel, 2 Switch 

Notes: 

1.  Awning configuration is specified at time of order, including awning length, fabric, color and 

electronics.  Check awning assembly against original purchase order. 

2.  Mounting screws are ordered separately.  Available in single awning or master pack quantities.  2 screw 

styles available: 1/4-20 x 1 self-drilling screws or 1/4 x 2" lag screws.  Screws available in White or Black. 

3.  The covered bezel (item 8) is optional and ordered separately.  Refer to page 7 for information about 

NFPA 1192 RV Standard, Section 6.4.9 (Switch Installation Requirements) 

4.  Item 7 is furnished with the BT12 Wireless Awning Control System kit when ordered. 

 

1

2

7

3

6

4

5

FL011

RETRACT

ON

EXTEND

OFF

Awning Cont

rol

RETRACT

ON

EXTEND

Awning 

Control

OFF

8

Summary of Contents for LATITUDE












Reviews: