background image

052979-003r5 

Printed in USA 

May, 2013 

 

I

NSTALLATION 

M

ANUAL

 

M

IRAGE 

P

ATIO 

A

WNING

This publication includes installation for the 

 Direct Response Auto-Retract System with DSK Style Switches 

RV

 

 

 

 

 

 

 

 

 

 

 

T

ABLE OF 

C

ONTENTS

 

Overview ........................................................................................................................................ 1

 

General Description ................................................................................................................................ 1

 

Mirage Patio Awning Specifications .................................................................................................... 1

 

Component Checklist.............................................................................................................................. 2

 

Installation ..................................................................................................................................... 3

 

Required Pre-Installation Parameters ..................................................................................................... 3

 

Mounting Plate Layout and Installation ................................................................................................... 3

 

Alternate Mounting Plate Attachment Method ..................................................................................... 4

 

Mounting the Awning Unit ....................................................................................................................... 5

 

Securing the Awning ............................................................................................................................... 5

 

Electrical Installation .................................................................................................................... 6

 

Important Notices:................................................................................................................................... 6

 

Switch Installation ................................................................................................................................... 6

 

Control Box Installation ........................................................................................................................... 7

 

Installing the RF Remote Receiver ......................................................................................................... 8

 

Programming the Receiver ................................................................................................................. 8

 

Operational Notes: .............................................................................................................................. 8

 

Ignition Lockout Sensor Installation (Optional) ....................................................................................... 9

 

Wiring Diagram –Direct Response System .......................................................................................... 10

 

Testing the System ............................................................................................................................... 11

 

Standard System Adjustments .................................................................................................. 12

 

Manual Override ................................................................................................................................... 12

 

Adjusting the Pitch ................................................................................................................................ 12

 

Setting the Motor Limits ........................................................................................................................ 13

 

Adjusting the OUT Limit Switch ......................................................................................................... 13

 

Adjusting the IN Limit Switch ............................................................................................................. 13

 

 

Carefree of Colorado 

2145 W. 6

th

 Avenue Broomfield, CO  80020 

a

 Scott Fetzer 

company

 

Summary of Contents for MIRAGE
















Reviews: