background image

3

ENG

 

WTS +0300130EN rel. 1.0 - 05.09.2022

GENERAL WARNINGS

FAILURE TO CAREFULLY HEED THE WARNINGS SHOWN IN THIS 
MANUAL COULD LEAD TO FIRE OR EXPLOSION AND CONSEQUENT 
DAMAGE TO PROPERTY, INJURY OR DEATH.

•  Do not store or use petrol or other flammable vapours and liquids 

in the vicinity of this or other appliances.

IF YOU SMELL GAS:

1.  Do not attempt to switch on any appliance;

2.  Do not touch any electrical switches; do not use telephones in 

the building;

3.  Call the gas supplier immediately from a neighbour’s phone. Fol-

low the instructions given by the gas supplier;

4.  If you cannot contact the gas supplier, call the fire brigade;

•  Installation and maintenance must be performed by a quali-

fied installer, service centre or gas supplier.

CAREL Industries reverse osmosis (RO) systems are advanced products, 
whose operation is specified in the technical documentation supplied 
with the product or can be downloaded, even prior to purchase, from the 
website www.carel.com. Each CAREL product, in relation to its advanced 
level of technology, requires setup/configuration/programming to be able 
to operate in the best possible way for the specific application. Failure to 
complete such operations, which are required/indicated in the user manu-
al, may cause the final product to malfunction; CAREL accepts no liability in 
such cases. The customer (manufacturer, developer or installer of the final 
equipment) accepts all liability and risk relating to the configuration of the 
product in order to reach the expected results in relation to the specific 
final installation and/or equipment. CAREL may, based on specific agree-
ments, act as a consultant for the installation/commissioning/use of the 
unit, however in no case does it accept liability for the correct operation 
of the RO system and the final installation if the warnings or suggestions 
provided in this manual or in other product technical documents are not 
heeded. In particular, as well as observing the above warnings and sug-
gestions, the following warnings must be observed for correct use of the 
product:

ELECTRIC SHOCK HAZARD: 

the RO system contains live electrical com-

ponents

.

 Disconnect the mains power supply before accessing inside 

parts or during maintenance and installation.

WATER LEAK HAZARD: 

the RO system automatically and constantly fills/

drains certain quantities of water. Malfunctions in the connections or in 
the humidifier may cause leaks.

Environmental conditions, fuel and power supply voltage must all com-
ply with the specified values. All other uses and modifications made to 
the appliance that are not authorised by the manufacturer are considered 
incorrect. Liability for injury or damage caused by the incorrect use of the 
appliance lies exclusively with the user.
Please note that the appliance contains live electrical devices. All service 
and/or maintenance operations must be performed by specialist and 
qualified personnel who are aware of the necessary precautions and are 
capable of performing the operations correctly and in accordance with 
the safety standards and legislation in force, with specific reference to: 

1.  Italian law no. 46/90: “Safety standards relating to systems in buildings”;
2.  Italian Presidential Decree no. 447 of 6 December 1991: “Regulations for 

the enforcement of law no. 46, dated March 5, 1990, on safety relating 
to systems in buildings”;

3.  Italian law no. 10/91: “Regulations for the enforcement of the national 

plan for energy savings and the development of renewable sources of 
energy”

CAUTION

The installation of the product must include an earth connection, using 
the Schuko plug available in the RO system.

Caution:
•  Disconnect the appliance from the mains power supply before access-

ing any internal parts.

•  Environmental and power supply conditions must conform to the val-

ues specified on the product rating labels.

•  The product is designed exclusively to demineralize drinkable water.
•  Only qualified personnel who are aware of the necessary precautions 

and able to perform the required operations correctly may install, oper-
ate or carry out technical service on the product.

•  Only water with the characteristics indicated in this manual must be 

used.

•  All operations on the product must be carried out according to the 

instructions provided in this manual and on the labels applied to the 
product. Any uses or modifications that are not authorised by the manu-
facturer are considered improper. CAREL declines all liability for any such 
unauthorised use.

•  Do not attempt to open the appliance in any way other than described 

in the manual.

•  Observe the standards in force in the place where the RO system is  

installed.

•  The appliance is not intended for use by persons (including children) 

with reduced physical, sensory or mental capabilities, or lack of expe-
rience and knowledge, unless they have been given supervision or in-
struction concerning use of the appliance by a person responsible for 
their safety.

•  Do not install and use the product near objects that may be damaged 

when in contact with water (or condensate). CAREL declines all liability 
for direct or indirect damage following water leaks from the humidifier.

•  Do not use corrosive chemicals, solvents or aggressive detergents to 

clean the inside and outside parts of the RO system, unless specifically 
indicated in the user manual.

•  Do not drop, hit or shake the RO system, as the inside parts and the 

linings may be irreparably damaged,

CAREL adopts a policy of continual development. Consequently, CAREL 
reserves the right to make changes and improvements to any product 
described in this document without prior warning. The technical speci-
fications shown in the manual may be changed without prior warning. 
The liability of CAREL in relation to its products is specified in the CAREL 
general contract conditions, published on the website www.carel.com 
and/or by specific agreements with customers; specifically, to the extent 
where allowed by applicable legislation, in no case will CAREL, its employ-
ees or subsidiaries/affiliates be liable for any lost earnings or sales, losses of 
data and information, costs of replacement goods or services, damage to 
things or people, downtime or any direct, indirect, incidental, actual, puni-
tive, exemplary, special or consequential damage of any kind whatsoever, 
whether contractual, extra-contractual or due to negligence, or any other 
liabilities deriving from the installation or use of the product, even if CAREL 
or its subsidiaries/affiliates are warned of the possibility of such damage.

Warnings 

Summary of Contents for Compact ROC 140





























































Reviews: