background image

lb-05073-04-EN 

Pag. 3 

30/09/14 

 

INTRODUCTION 

 
Thoroughly  read  the  instructions  contained  in  this  booklet  because  it  gives  important  information  regarding  safety  for  installation, 
use and maintenance. 
Keep this booklet in a safe and accessible place for further consultation. 
After unpacking check that the machine is not damaged. 
If in doubt, do not use the machine and contact an Authorised Service Centre. 
All packing materials (plastic wrapping, polystyrene, nails, etc.) are potentially dangerous and must be kept out of children’s reach 
and disposed of in a safe manner for the environment. 
Before connecting the machine to the power supply make sure that the rating information of the machine correspond to that of the 
power supply: if the power socket is not compatible with the plug of the machine (if supplied), replace the socket with a proper one, 
ensuring that the size of the cable is suitable for the absorbed power of the machine. 
The use of adapters, multiple power boards and extension cords is not recommended. 
If  it  is  absolutely  necessary,  then  use  only  single  or  multiple  adapters  and  extension  cords  which  comply  with  current  safety 
regulations,  ensuring  also  that  the  electricity  load  capacity  of  the  single  adapters  and  extension  cords  and  the  maximum  power 
rating of the multiple adapters is suitable. 
The  appliance  should  be  placed  on  a  stable  flat  surface  with  the  bodywork  at  a  minimum  distance  of  20mm  from  the  back  wall, 
furthermore, it must be installed taking into account that the highest shelf must sit at a height that is at least 1.5 mt. 
 
During installation, fit a device that guarantees disconnection from the mains, duly sized according to the power of the equipment 
(see rating plate), as well as protection against leakage current with a value equal to 30mA.This cut-off device must be assembled 
on the power supply line in compliance with installation rules. 
 
This machine must be used only for the purpose it was designed: cool alimentary liquids. 
Any other use is to be considered inappropriate and therefore dangerous. 
 
The manufacturer declines all responsibility for damage caused by any improper, incorrect and unreasonable use of the machine. 
The use of any electric appliance implies the observance of some fundamental rules. 
More specifically: 

do not touch the appliance with your hands or feet wet or damp 

do not use the appliance with bare feet 

do not pull the power cord to disconnect the plug from the power socket 

dot not leave the appliance exposed to the weather (rain, sun, frost) 

do not let children or untrained persons use the appliance. 

 
Before carrying out any cleaning and maintenance, disconnect the appliance from the power supply, pulling the plug from the power 
socket and turning off the main switch. 
In case of failure or malfunction turn the machine off and do not attempt to carry out any repairs or direct operations on the machine. 
All repairs must be carried out in an authorised service centre, using original spare parts only. 
Failure to comply with the above recommendations will compromise the safety of the machine and the warranty conditions. 
If this machine is no longer used we recommend that it is made inoperative by disconnecting the cable from the power supply, and 
all potentially dangerous parts are made harmless, especially to protect children who might use the machine for their games. 
 
 

SPECIAL NOTES 

 
Installation must be carried out according to the manufacturer’s instructions. 
An  incorrect  installation  can  cause  damage  to  persons,  animals  or  things;  the  manufacturer  declines  all  responsibility  for  such 
situation. 
The electrical safety of this machine can be guaranteed only if correctly connected to an efficient earth circuit as indicated by current 
electrical safety regulations. 
 

 

 

It is necessary to check this fundamental safety prerequisite, and in case of doubt, ask a professionally qualified technician to check 
the circuit. 
The manufacturer declines all responsibility for any damage caused by failure to earth the equipment. 
In order to avoid any dangerous overheating, we recommend that the power cord be fully unwound. 
Do not leave the machine connected unnecessarily. 
 
Turn off the machine when not in use. 
Place the machine at an adequate distance from walls, objects, etc. 
The  power  cord  of  this  machine  must  not  be  replaced  by  the  customer.  In  case  of  damage  to  the  cord,  contact  exclusively  an 
authorised service centre to have it replaced. 
 

Summary of Contents for A01-PLUS -V2





















Reviews: