background image

PARTS LIST

ITEM  

NO.

PART NO.

DESCRIPTION

1600-HFxxxx  

FLAT TIP  

QTY.

1600-xTxxxx  

TWIST TIP  

QTY.

1

54-6007

AIR VALVE HOUSING

1

1

2

54-5935-K5

NEEDLE RETURN SPRING KIT (MULTI-PACK)

1

1

3

54-6131-K

SPINDLE SEAL & SPRING KIT

1

1

3a

REAR SEAL

1

1

3b

AIR VALVE SPRING

1

1

3c

VALVE SEAL

1

1

3d

FRONT SEAL

1

1

4

54-5815

SPREADER VALVE ASSEMBLY

1

1

4a

VALVE STEM

1

1

4d

VALVE BODY

1

1

4c

SN-71X-K2 

O-RING (MULTI-PACK)

1

1

4b

 

    PIN

1

1

4e

 

    SNAP RING

1

1

5

54-5937

AIR VALVE & FLUID NEEDLE ASSEMBLY

1

1

6

54-6114

TRIGGER NUT

1

1

7

54-6115

TRIGGER SCREW

1

1

8

SPA-71-K5  

SPA-71-K10

BAFFLE PLATE (MULTI-PACK)

1

1

9

54-5811-K

FLUID NOZZLE & GASKET (FLAT TIP)

1

54-5833-K

FLUID NOZZLE & GASKET (TWIST TIP)

1

9a

SPA-98-K5

 

SPA-98-K10

GASKET (MULTI-PACK)

10

SEE PAGE 10

REVERSABILE TWIST TIP

11

54-5924-K

HVLP TWIST TIP AIR CAP ASSEMBLY

1

12

SEE PAGE 10

FLAT TIP ASSEMBLY

SEE PAGE 10

FINE FINISH FLAT TIP ASSEMBLY

13

54-6030-K

AA10+ AIR CAP ASSEMBLY

1

14

SN-9-K3

AIR INLET (MULTI-PACK)

1

1

15

SLOTTED ROUND HEAD SCREW, 1/4" - 20 x 1/2"

1

1

16

54-6019 

TRIGGER

1

1

17

54-6015

FLUID TUBE ASSEMBLY

1

1

17a

FLUID TUBE ADAPTER

1

1

17b

54-5896-K5

FLUID TUBE RETAINER (MULTI-PACK)

1

1

17c

54-5899

FERRULE NUT

1

1

17d

54-6017

FILTER BRACKET

1

1

17e

54-1835 

FLUID FILTER, 100 MESH

1

1

17f

54-4726-K

DISC FILTER BODY, 1/4" NPS (M)

1

1

17g

DISC FILTER RETAINER

1

1

18

54-5897

JIC #5 FLUID INLET FITTING (SOLD SEPARATELY)

19

72-2360

SWIVEL ADAPTER, 1/4" NPS M X F (SOLD SEPARATELY)

20

SPN-7

TOOL

1

1

Parts are included within the following packing kits:

   Parts are included in kit: GTI-428-K5

ALTERNATE ITEMS (SOLD SEPERATELY):

   54-1836 FLUID FILTER, 60 MESH

   54-6018 TRIGGER, SHORT PULL

EN

77-3130-R4  (5/2019)

9 / 16

www.carlisleft.com

Summary of Contents for Binks TROPHY AA 1600

















Reviews: