Carrera RC 370503026, Assembly And Operating Instructions Manual

6

moved from the toy.   Rechargeable batteries should be removed from the  product  

before charging. The battery in controller is not replaceable. Supply terminal are 

not to be short-circuited. Only use the batteries recommended or equivalent types. 

Battery chargers used with the toy are to be regularly examined for damage 

to the cord, plug, enclosure and other parts, and in the event of such damage, 

they must not be used until the damage has been repaired. The toy is only to 

be connected to Class II  equipment bearing the following symbol. 

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to 

the following two conditions: 

(1)  this device may not cause harmful interference, and 

(2)  this device must accept any interference received, including interference 

that may cause undesired operation. 

NOTE: 

This product has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 

designed  to  provide  reasonable  protection  against  harmful  interference  in  a 

residential installation. This product generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there 

is no guarantee that interference will not occur in a particular installation. If the 

product does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged 

to try to correct the interference by one or more of the following measures : 

•  Reorient or relocate the receiving antenna.a 

•  Increase the separation between the product and receiver. 

•  Connect the product into an outlet on a circuit different from that to which the 

receiver is connected. 

•  Consult the dealer or an experienced radio/TV technician for help.

IC statement

The device contain license-exempt transmitter(s)/ receiver(s) that comply with 

Innovation,  Science  and  Economic  Development  Canada’s  licence-exempt 

RSS(s). Operation is subject to the following two conditions: 

1. The device must not cause interference; 

2. The device must accept any interference, including interference that may 

cause undesired operation of the device. 

Guidelines and warnings for the use of LiPo rechargeable batteries 

•  You have to charge the attached 3.7 V   430 mAh /1.591 Wh LiPo rechargea-

ble battery in a safe place and at a safe distance to flammable material.

•  Never leave the battery unattended while it is charging 

•  After a flight, the rechargeable battery has to cool down to the ambient air 

temperature before charging it.

•  You  must  always  use  the  corresponding  LiPo  charging  unit  (USB  cable  / 

remote control). In case of non-compliance with these directions there is a 

danger of fire resulting in a health risk and/or damage to property. NEVER 

use any other battery charger.

•  Should the rechargeable battery swell or deform while discharging or recharg-

ing, you have to immediately stop charging or discharging the battery. Take the 

battery out as quickly and carefully as possible and place it in a safe and open 

area offside any inflammable material and watch it for at least 15 minutes. In 

case you continue charging or discharging a battery which has already started 

to swell or deform there is a danger of fire! Even in case of slight deforming or 

ballooning the rechargeable battery has to be taken out of operation.

•  Store the rechargeable battery at ambient temperature in a dry place.

•  

Always recharge the battery immediately after use to prevent its becom-

ing deep discharged. Please make sure to allow a pause of about 20 min-

utes between finishing the flight and recharging the battery. Recharge 

the battery occasionally (suggested every 2-3 months). Failure to treat 

the battery as described above can lead to its becoming defective.

•  When transporting or temporarily storing the rechargeable battery the tem-

perature should be between 5-50°C. If possible, do not store the battery or 

the model in a car and do not expose it to direct sunlight. In case the battery 

is broiled it can be damaged or catch fire. 

Note:

 If the battery voltage/output is low you will recognise that a considera-

ble trim and/or controlling is necessary to avoid that the Quadrocopter starts 

trundling. This usually  occurs before reaching a battery voltage of 3 V and it 

is a good moment to end the flight.

Contents of package

1

1 x Quadrocopter 

1 x One-hand controller

1 x USB charging cable 

1x Rechargeable Battery

Charging the LiPo battery and one-hand controller

Make sure that you charge the LiPo rechargeable battery or one-hand con-

troller supplied only using the LiPo charger (USB cable) supplied. If you try to 

charge the rechargeable battery or one-hand controller with another LiPo bat-

tery charger or any other charger, this might cause serious damage. Please 

carefully read the previous chapter with warnings and guidelines on the usage 

of rechargeable batteries before proceeding. Supply terminals are not to be 

short-circuited. You can charge the rechargeable battery or one-hand con-

troller fitted in the quadrocopter with its USB charging cable from a USB port: 

2a

Charging via computer:

•  Rechargeable batteries are to be removed from the model before 

being charged. 

•  Connect the USB charging cable with the USB port of a computer. The 

LED on the USB charger cable lights green indicating that the charger 

unit is correctly connected to the computer.If you plug in the quadro-

copter or one-hand controller with a discharged battery, the LED on the 

USB charging cable no longer lights up, showing that the quadrocopter 

battery or one-hand controller is being charged. The USB charging ca-

ble and the charging socket on the quadrocopter or one-hand controller 

are designed to make incorrect connection impossible.

•  It takes about 60 minutes to recharge a discharged battery (but NOT a 

deep-discharged one). When the battery or one-hand controller is fully 

charged, the LED display on the USB charger cable lights up green again.

Note: when supplied, the lipo-battery is already partially charged. So the 

first charging cycle may well take less time.
It is essential to follow the connection sequence given above! 

Undo the plugged connection on the Quadrocopter when you are not 

using the Quadrocopter. Failure to observe this precaution may cause 

battery damage!

2b

Insertion of the rechargeable batteries into the Quadrocopter

•  Use a screwdriver to open the cover of the battery compartment. Insert 

the battery. Close the battery compartment.

•  If the LED on the quadrocopter or one-hand controller flashes slowly, 

you must change or charge the battery.

Putting on the one-hand controller

3

Place the rectangular module with the power switch on the flat of your 

palm so that your thumb fits through the thumb loop. Push your index 

finger into the second loop provided. Close the wrist strap on your palm. 

Frequency bind between model and remote control

4

The Carrera RC Quadrocopter and the one-hand controller automatically 

link up renewed with every operational start-up. If initially there are any 

problems with communication between the Carrera RC Quadrocopter and the 

one-hand controller, please carry out a new frequency bind.
•  Connect the battery in the model.

•  Press the ON/OFF button on the top.

•  The LEDs on the quadrocopter now flash rhythmically.

•  Switch on the one-hand controller at the power switch.

•  

WARNING! Immediately after switching it on, place the Quadrocopter 

on a flat and level surface. The gyro-system will then set itself automat-

ically. Also ensure that the quadrocopter is aligned correctly and its 

front (red rotor blades) points away from you.

•  The binding has now been successfully established.

•  The LEDs on the one-hand controller or quadrocopter now light up permanently.

Description of the Quadrocopter

5

1.  Rotor system

2.  Rotor protection cage

3.  LEDs

6

4.  Battery cable

5.  Quadrocopter connecting plug

6.  Battery compartment 

7.  Anti-collision sensors

NOTE:

 The function of the anti-collision sensors can be disrupted by 

light and direct sunshine. The sensors are unable to identify window 

panes as an obstacle. 

Range of functions of the remote control 

7

1.  Power ON / OFF (OFF = hold for 10 sec.)

2.  Index finger loop with button

3.  Thumb loop

ENGLISH