15
To restore the Control Unit to factory settings the Control Unit offers
a reset function.
Switch off the Control Unit and keep the “ESC/PACE CAR”
4
but-
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaffected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
After 20 minutes of non-usage the Control Unit switches to ener-
gy-saving mode and all displays such as Position Tower, Driver
Displays and Startlight are turned off. To reactivate the controller,
switch it off for 2 or 3 seconds, then switch it on again. All settings
will be kept.
Car programming
from DIGITAL 132
to Evolution (analogue)
Push the switch for changing the running direction acc. fig.
1
.
Place car on the Evolution track and push speed controller´s tap-
pet three times (thumb). For Carrera DIGITAL 132 operation mode
return the switch to original position.
Replacement of double sliding
contact and guide keel
2 a
2 b
1
Advice:
• It is recommended to always take out and change only one grinder.
• Never pull the vehicle backwards, because the grinders could be
damaged otherwise.
1
Please carefully pull out the guide keel according to fig.
1
.
2
When changing the double contact brushes please take care
that in stage one the upper contact brush
2
a
is only pulled out
partly and that in stage two the double contact brush can be pulled
out completely with the contact brush
2
b
. For inserting please
proceed the same way.
Changing the rear axle
1
2
3
Take off the vehicle´s upper part from the chassis as per fig.
1
.
Remove the axles from the bearings positions with pressure (
2
).
Insert new axle. Pay attention to the correct position of the axle
bearings (
3
).
Maintenance and care
1
2
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior to
cleaning.
1
Racetrack:
Keep the track surface and track slots clean with a
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
2
Car check:
Clean axle and wheel bearings, pinion gears, gear-
wheels and bearings and lubricate using a resin- and acid-free
grease. You can use a toothpick or similar as aid. Regularly check
the condition of sliding contacts and tyres.
Troubleshooting
Driving tips
Troubleshooting:
In case of any malfunctions, please check the following:
• Has the connection to the power supply been established cor-
rectly?
• Have transformer and speed controllers been connected correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track‘s current feed will be switched off automatically for 5
seconds, if there is an electrical short circuit: this will be notified by
audible and visual signals.
• Are the cars placed on the track in running direction? In case of
non-functioning push the running direction switch which is on the
car´s bottom.
Note:
During operation small car parts as spoilers or mirrors may get off or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.
Driving technique:
• You can drive fast along the straight track but you should brake
before the curve and then accelerate again when coming out of the
curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
Note:
When using track systems which are not manufactured by
Carrera the existing guide keel has to be replaced by the spe-
cial guide keel (#20085309). While using the Carrera crossing
(#20020587) or high banked curve 1/30° (#20020574) slight driving
noise might occur which is due to the full-scale genuineness and
does not affect flawless operation.
Technical specifications
Output voltage: Toy transformer
14,8 V
51,8 VA
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode.
The LED is no longer lit.
CURRENT CONSUMPTION < 0,5 watt / 0,5w
To reactivate the controller, switch it off for 2 or 3 seconds, then
switch it on again. The racetrack is then once again in standby
mode.
4.) Off-state = power supply unit disconnected from mains supply
This device is marked by ”selective sort throught” symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized ”sorting/collecting” sys-
tem in accordance with European directive 2012/19/EU, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are
not going through special collecting, are potentially dangerous for
environment and human health, because of dangerous substance.
Output voltage: Toy transformer
14,8 V
42,9 VA
Electricity modes:
1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode.
The LED is no longer lit.
CURRENT CONSUMPTION < 0,5 watt / 0,5w
By switching it off and on again, the racetrack returns to
‘Play’ mode.
4.) Off-state = power supply unit disconnected from mains supply
