11
Setting fuel tank capacity
Pit Stop 30346
1
3
2
3
1 – 10
1 – 10
(individually for one and/or several cars)
1
Activate fuelling function at the Black Box.
2
Plug any speed controller in connector 3. Switch off Black Box,
place car/s on the track, push lane-change-button and keep it
pushed while Black Box is switched on again. Don´t release the
lane-change-button until the 1st LED lights red. Fuel capacity is
set by pushing lane-change-button. Confi rm by pressing speed
controller´s tappet (=> middle LED will light).
Before the start return speed controller to the original connector!
3
1 LED on = low fuel capacity
5 LEDs on = full tank
Refuelling:
Depending on the fuel capacity the car´s lights start to fl ash after
some time, the car slows down and might start to stutter. For refuel-
ling enter the Pit Stop and release the speed controller´s tappet.
(Fuelling amount depends on car´s standing time in the Pit Stop).
a) Filling up: wait until car´s lights stop fl ashing.
b) Partial refuelling: start while car´s lights still fl ash.
c) Non-refuelling: car drives on at reduced speed.
Car programming
from DIGITAL 132
to Evolution (analogue)
Place car on the Evolution track and push speed controller´s tappet
three times (thumb). Push the switch for changing the running direc-
tion acc. fi g.
1
. For Carrera DIGITAL 132 operation mode return
the switch to original position.
Replacement of double sliding
contact and guide keel
2 a
2 b
1
Advice:
• It is recommended to always take out and change only one
grinder.
• Never pull the vehicle backwards, because the grinders could be
damaged otherwise.
1
Please carefully pull out the guide keel according to fi g.
1
.
2
When changing the double contact brushes please take care
that in stage one the upper contact brush
2
a
is only pulled out
partly and that in stage two the double contact brush can be pulled
out completely with the contact brush
2
b
. For inserting please
proceed the same way.
Changing the rear axle/
engine/engine block
1
2
3
4
Changing the rear axle
Loosen screw according to fi g.
1
. Take out the rear axle including
the engine block with slight pressure and remove the axle carefully
2
. Insert new axle, insert engine block while the nose clicks into
the chassis and screw together
3
.
Changing the engine/engine block
Procedure as with changing the rear axle. However, the cable bet-
ween engine and car board needs to be loosened or sticked toge-
ther (see fi g.
4
).
Note
:
Having changed the engine the vehicle may not be operated until
fully assembled.The engine may only be changed by adults.
Maintenance and care
1
2
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior to
cleaning.
1
Racetrack:
Keep the track surface and track slots clean with a
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
2
Car check:
Clean axle and wheel bearings, pinion gears, gear-
wheels and bearings and lubricate using a resin- and acid-free
grease. You can use a toothpick or similar as aid. Regularly check
the condition of sliding contacts and tyres.
Troubleshooting
Driving tips
Troubleshooting:
In case of any malfunctions, please check the following:
• Has the connection to the power supply been established cor-
rectly?
•
Have transformer and speed controllers been connected
correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track‘s current feed will be switched off automatically for 5
seconds, if there is an electrical short circuit: this will be notifi ed by
audible and visual signals.
• Are the cars placed on the track in running direction? In case of
non-functioning push the running direction switch which is on the
car´s bottom.
Note:
During operation small car parts as spoilers or mirrors may get off or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.
Driving technique:
• You can drive fast along the straight track but you should brake
before the curve and then accelerate again when coming out of the
curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
Note:
When using track systems which are not manufactured by
Carrera the existing guide keel has to be replaced by the special
guide keel (#85309). While using the Carrera crossing (#20587) or
high banked curve 1/30° (#20574) slight driving noise might occur
which is due to the full-scale genuineness and does not aff ect fl aw-
less operation.
All Carrera spare parts are available in the webshop:
www.carrera-toys.com
Delivery exclusively to Germany, Austria, Netherlands, Belgium and
Luxembourg.
Technical specifications
Output voltage: Toy transformer
14,8 V
51,8 VA
This device is marked by “selective sort throught” symbol related to
sort through domestic, electric and electronic, waste.
This means the product must be treated by a specialized “sorting/
collecting” system in accordance with European directive 2002/96/
CE, to reduce the impact upon environment.
For more precise information, please contact your local administra-
tion.
Electronical product which are not going through special collect-
ing, are potentially dangerous for environment and human health,
because of dangerous substance.
Output voltage: Toy transformer
14,8 V
42,9 VA
Summary of Contents for DIGITAL 132 30139 NASCAR
Page 1: ...3 013 9 N A S C A R...
