Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 117 / 568

background image

Axxius 800 - Release 2.2

5-17

CLI Commands

add

add (router-lan) filter protocol

Use the add (router-lan) filter protocol command to add a protocol filter to the table of
Layer 2 filters applied to the specified LAN interface. Note that you only need to identify
either an Ethernet or IEEE value, but not both. The other should be entered as 0.

Syntax:

add {rtr_lan-addr} filter protocol {ether-type}

{ieee-value} {"filter-name"}

Example:

add 2:1 filter protocol 0x0807 0x0 "XNSrule"

The example will add a custom layer-2 filter that will match all XNS packets.

{rtr_lan-addr}

The Router address is in the form {slot:port} or {slot "profile-name"}.

{ether-type}

This assigned Ethernet value for this protocol. The ether-type is entered as a 16-bit
hexadecimal value. See Ethernet Protocol Types on page D-6 for protocol number and
descriptions.

{ieee-value}

The assigned IEEE value for this protocol. The IEEE value is the same as the SDAP and
SSAP values in a SNAP packet. The match value is entered as a 8-bit hexadecimal value.

{"filter-name"}

A symbolic name given to identify a filter rule. This name must be enclosed in quotes, with
a maximum of 8 characters.

slot

Slot number (1-8) that contains the Router card.

port

Port number of the Router.

"profile-name"

The profile name for the Router interface. Name must be enclosed in
quotes, with a maximum length of 11 characters.

«
...
115
116
117
118
119
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

AirPlus G DWL-G710

Brand: D-Link Pages: 5

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

Brand: Ubiquiti Pages: 40

RDX QuikStation 4

Brand: Tandberg Data Pages: 2

RUGGEDSWITCH RS900G

Brand: RuggedCom Pages: 23

Brand: XMOS Pages: 6

SmartNode 4520 Series

Brand: Patton electronics Pages: 90

Brand: TP-Link Pages: 37

Brand: Microtek Pages: 25

Brand: Abocom Pages: 1

Brand: Valcom Pages: 4

Brand: Allied Telesis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands