Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 118 / 568

background image

5-18

Axxius 800 - Release 2.2

CLI Commands

add

add (router-lan) secondary ip address

Use the add (router-lan) secondary ip address command to add a secondary IP address and
subnet to the specified LAN interface. The Router will then be capable of routing between the
various subnets on the LAN interface or between any of the LAN subnets and any WAN subnet.
A maximum of 8 secondary IP addresses can be added to the LAN interface.

Syntax:

add {rtr_lan-addr} secondary ip address

{ip-addr [mask]|ip-addr/bits}

Example:

add 4:1 secondary ip address 192.168.1.1 255.255.255.0

The example will add a secondary IP address of 192.168.1.1 and a subnet mask
of 255.255.255.0.

To view the secondary IP addresses, use the show 4:1 command

{rtr_lan-addr}

The Router address is in the form {slot:port} or {slot "profile-name"}.

{ip-addr [mask]|ip-addr/bits}

slot

The slot number (1-8) that contains the Router card.

port

Port number of the Router.

"profile-name"

The profile name for the Router interface. Name must be enclosed
in quotes, with a maximum length of 11 characters.

ip-addr

The IP address of the Host to query, in the form of xxx.xxx.xxx.xxx,
where xxx is between 0-255.

mask

The mask of the secondary IP address, in the form of
xxx.xxx.xxx.xxx, where xxx is between 0-255.

bits

The subnet mask, specified as the number of ones bits in the mask
value. Range is between 1-32.

«
...
116
117
118
119
120
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Brand: N-Tron Pages: 101

Wireless Router

Brand: Watchguard Pages: 11

Brand: D-Link Pages: 32

Brand: D-Link Pages: 28

Brand: D-Link Pages: 48

Brand: D-Link Pages: 83

Brand: D-Link Pages: 155

Brand: H3C Pages: 1057

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: TP-Link Pages: 2

Brand: Aztech Pages: 2

PowerBeam AC Gen2

Brand: Ubiquiti Pages: 22

Brand: Macsense Pages: 13

Brand: Caton Pages: 18

Brand: BHU NETWORKS Pages: 75

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: Alcatel-Lucent Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands