Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 145 / 568

background image

Axxius 800 - Release 2.2

5-45

CLI Commands

delete

delete (router) remote

Use the delete (router) remote command to delete a remote WAN profile from the WAN
profile table on the specified Router card.

Syntax:

delete {rtr_card-addr} remote {"profile-name"}

Example:

delete 6 remote "Texas"

The example will delete a remote WAN named "Texas" from the WAN profile
table for the Router in slot 6.

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

{"profile-name"}

The name of the remote WAN profile to delete. This name must be enclosed in quotes, with
a maximum of 12 characters.

delete (router) snmp community

Use the delete (router) snmp community command to delete an SNMP community entry on
the specified Router card.

Syntax:

delete {rtr_card-addr} snmp community

{"community-name"} {ip-addr}

Example:

delete 2 snmp community "commune" 192.168.100.245

The example will delete the previously added SNMP community named
"commune" from the TSR in slot 2.

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

{"community-name"}

The name of an existing community with a maximum of 12 characters, enclosed in quotes.

{ip-addr}

The IP address of the host that can access the SNMP agent via this community, in the form
of xxx.xxx.xxx.xxx, where xxx is between 0-255. The address "0.0.0.0" allows any host.

«
...
143
144
145
146
147
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Verizon DSL-2750B

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: Vanguard Pages: 121

Brand: Paradyne Pages: 2

Brand: ZyXEL Communications Pages: 2

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Brand: Conel Pages: 32

Brand: XtendLan Pages: 52

Brand: AMX Pages: 1

Brand: Supermicro Pages: 15

Brand: SafeHome Pages: 24

AlterPath Manager 2500

Brand: Cyclades Pages: 368

Brand: UNICORECOMM Pages: 19

NetCon FBR-1409TX

Brand: LevelOne Pages: 88

Brand: Variscite Pages: 17

RuggedSwitch RS500

Brand: RuggedCom Pages: 16

Brand: Idis Pages: 40

Brand: Alloy Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands