manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

5-48

Axxius 800 - Release 2.2

CLI Commands

delete

delete (router-lan) filter

Use the delete (router-lan) filter command to delete a single filter rule from the table of Layer 
2 filters applied to the specified LAN interface. 

Syntax:

delete {rtr_lan-addr} filter 

{address|custom|protocol|all} {"filter-name"}

Example:

delete 2:1 filter address "Server1"

This example will delete a previously created address filter names "Server1".

{rtr_lan-addr}

The Router address is in the form {slot:port} or {slot "profile-name"}.

{address|custom|protocol|all}

{"filter-name"}

A symbolic name given to identify a filter rule. This name must be enclosed in quotes, with 
a maximum of 8 characters.

slot

Slot number (1-8) that contains the Router card

port

Port number of the Router.

"profile-name"

The profile name for the Router interface. Name must be enclosed in 
quotes, with a maximum length of 11 characters.

address

A previously created address filter

custom

A previously created custom filter

protocol

A previously created protocol filter

all

All filter rules. this options does not require a filter-name to follow

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
CallDirect CD Series At Command Manual preview
CD Series
Brand: CallDirect Pages: 33
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
Paradyne FrameSaver DSL 9788 Router Installation Instructions Manual preview
FrameSaver DSL 9788 Router
Brand: Paradyne Pages: 28
Ubiquiti airMAX NanoBridge M NBM3 Quick Start Manual preview
airMAX NanoBridge M NBM3
Brand: Ubiquiti Pages: 24
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Brand: PairGain Pages: 80
Lantronix WP2002000-01 User Manual preview
WP2002000-01
Brand: Lantronix Pages: 75
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
NETGEAR DGN2200M - Wireless-N 300 Router User Manual preview
DGN2200M - Wireless-N 300 Router
Brand: NETGEAR Pages: 95
Proxim Lynx.GX 16T Installation And Management Manual preview
Lynx.GX 16T
Brand: Proxim Pages: 45
ADTRAN NetVanta 1224R Specifications preview
NetVanta 1224R
Brand: ADTRAN Pages: 4
Patton electronics 593/25, 593/45, 593/TB, RS-422, RS-485 User Manual preview
593/25, 593/45, 593/TB, RS-422, RS-485
Brand: Patton electronics Pages: 8
Ecos SECURE BOOT STICK FX Administrator'S Manual preview
SECURE BOOT STICK FX
Brand: Ecos Pages: 22
Cambium Networks PTP 850E Installation Manual preview
PTP 850E
Brand: Cambium Networks Pages: 99
LG N4B2N Specifications preview
N4B2N
Brand: LG Pages: 2
LG V-net ACS PWFMDB000 Installation & User Manual preview
V-net ACS PWFMDB000
Brand: LG Pages: 48
LG LST-270T User Manual preview
LST-270T
Brand: LG Pages: 24

Brands by name

Popular brands

Load more brands