Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 152 / 568

background image

5-52

Axxius 800 - Release 2.2

CLI Commands

delete

delete (router-lan) static ipx network

Use the delete (router-lan) static ipx network command to delete a static IPX network
(route) to the specified LAN interface.

Syntax:

delete {rtr_lan-addr} static ipx network {network}

{next-hop-ip-addr}

Example:

delete 3:1 static ipx network 0x11 0x00e09700e9cd

The example will delete a static IPX route to network 0x11, using a next hop
Router at MAC address 00:e0:97:00:e9:cd, from the LAN interface on the
Router card in slot 3.

{rtr_lan-addr}

The Router address is in the form {slot:port} or {slot "profile-name"}.

{network}

The IPX network number in HEX (0x...).

{next-hop-ip-addr}

The MAC address of the next hop Router, in the form a 6-octet HEX value, in the form
0xxxxxxxxxxxxx. Please note the address is preceeded by 0x.

slot

Slot number (1-8) that contains the Router card.

port

Port number of the Router.

"profile-name" The profile name for the Router interface. Name must be enclosed in

quotes, with a maximum length of 11 characters.

«
...
150
151
152
153
154
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Brand: D-Link Pages: 10

Brand: Campbell Pages: 42

Brand: ICP DAS USA Pages: 8

Brand: WaiLan Pages: 27

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

Brand: red lion Pages: 5

SinoCon C2000-C2-SHK0401-BB1

Brand: KonNad Pages: 12

Brand: Avaya Pages: 73

IPLink 2603 Series

Brand: Patton Pages: 120

Brand: BinTec Pages: 34

Brand: Chaparral Pages: 96

Brand: Nexxt Pages: 2

Brand: C&H Technologies Pages: 50

Brand: Cabletron Systems Pages: 56

Barricade SMC7908VoWBRA2

Brand: SMC Networks Pages: 2

Brand: Open House Pages: 2

Brand: Cisco Pages: 122

Brand: SOYO Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands