manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

xvi

Axxius 800 - Release 2.2

Table of Contents

 

log   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62

ping   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-63

print  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64

print config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64

print help  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65

rename (router)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-65

reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66

reset (controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66

reset (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66

reset (router) coldboot  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67

restore   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67

restore defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67

rtrping   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-68

set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69

set alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71

set autoexit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-71

set (bri) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-72

set (bri) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-73

set (bri) pmsync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-73

set cclabel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74

set clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-74

set clock (1 and 2)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75

set date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-75

set (ds0)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-76

set (ds1)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-78

set (ds1 card)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-81

set (ds3)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-83

set ethernet ip address  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86

set external alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-86

set (fxo)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87

set (fxsPS or fxsPSM)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88

set id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-88

set idle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-89

set ip gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-89

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
D-Link DVG-7022S Quick Installation Manual preview
DVG-7022S
Brand: D-Link Pages: 7
D-Link DIR-878 Quick Installation Manual preview
DIR-878
Brand: D-Link Pages: 41
IBM 51 Troubleshooting Manual preview
51
Brand: IBM Pages: 248
Paradyne 4300 Installation Instructions Manual preview
4300
Brand: Paradyne Pages: 22
H3C SR6600 SPE-FWM Vxlan Command Reference preview
SR6600 SPE-FWM
Brand: H3C Pages: 45
H3C SR6600 SPE-FWM Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 80
H3C MSR 5600 Configuration Manual preview
MSR 5600
Brand: H3C Pages: 46
H3C MSR 5600 Comware 7 Vxlan Command Reference preview
MSR 5600
Brand: H3C Pages: 45
H3C MSR 3600 Quick Start preview
MSR 3600
Brand: H3C Pages: 4
H3C SR6600 SPE-FWM Fundamentals Configuration Manual preview
SR6600 SPE-FWM
Brand: H3C Pages: 184
Magnadyne RV2458 User Manual preview
RV2458
Brand: Magnadyne Pages: 13
Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Abocom PLS342 Specification Sheet preview
PLS342
Brand: Abocom Pages: 2
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Brand: Schrack Technik Pages: 2
eWON 2101CD Installation Manual preview
2101CD
Brand: eWON Pages: 34
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Brand: Riverbed Pages: 82

Brands by name

Popular brands

Load more brands