manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

Axxius 800 - Release 2.2

5-105

CLI Commands

set

set (router) dhcp server duration

Use the set (router) dhcp server duration command to set the lease duration that the 
DHCP server applies to client assignments.

Syntax:

set {rtr_card-addr} dhcp server duration 

{hours:minutes}

Example:

set 5 dhcp server duration 3:45

The example set the lease duration for the DHCP server on the Router in slot 5 
to 3 hours and 45 minutes.

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

{hours:minutes}

The lease duration in hours and minutes, in the form of HH:MM. 
HH = 1-999, MM = 1-60. 

set (router) dhcp server netbios nameserver

Use the set (router) dhcp server netbios nameserver command to set the NetBIOS Name 
Server (NBNS - RFC 1001/1002) that the DHCP server provides to clients.

Syntax:

set {rtr_card-addr} dhcp server netbios nameserver 

{1|2} {ip-addr}

Example:

set 5 dhcp server netbios nameserver 1 192.168.100.80

Note: DHCP server must first be enabled with the "startaddr" command. See set 
(router) dhcp server startaddr on page 5-107.

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

{1|2}

The NetBIOS Name Server entry. 

{ip-addr}

The NBNS IP address, in the form of xxx.xxx.xxx.xxx, where xxx is between 0-255. 

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
4RF Aprisa LTE Quick Start Manual preview
Aprisa LTE
Brand: 4RF Pages: 7
Wattle Pegasus Quick Installation Manual preview
Pegasus
Brand: Wattle Pages: 6
Baicells Nova430i Quick Manual preview
Nova430i
Brand: Baicells Pages: 8
IBM E12 Quick Reference Manual preview
E12
Brand: IBM Pages: 4
ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Brand: ICP DAS USA Pages: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Brand: ICP DAS USA Pages: 15
ICP ZT-2550 Quick Start Manual preview
ZT-2550
Brand: ICP Pages: 14
Server Technology Sentry Global Security Modem Installation And Operation Manual preview
Sentry Global Security Modem
Brand: Server Technology Pages: 22
NETGEAR WAG302 Installation Manual preview
WAG302
Brand: NETGEAR Pages: 2
Perle P841 Specifications preview
P841
Brand: Perle Pages: 2
Lanner NCA-1040 User Manual preview
NCA-1040
Brand: Lanner Pages: 59
X-Micro IEEE 802.11b User Manual preview
IEEE 802.11b
Brand: X-Micro Pages: 49
Airlink101 AR325W Quick Installation Manual preview
AR325W
Brand: Airlink101 Pages: 13
Paradyne Hotwire 8323 Installation Instructions Manual preview
Hotwire 8323
Brand: Paradyne Pages: 6
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Brand: IMC Networks Pages: 13
SMC Networks Barricade SMC7908VoWBRA2 Specifications preview
Barricade SMC7908VoWBRA2
Brand: SMC Networks Pages: 2

Brands by name

Popular brands

Load more brands