manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

Axxius 800 - Release 2.2

5-149

CLI Commands

set

set (router-lan) up/down

Use the set (router-lan) up/down command to set the specified LAN interface up or down. 
When the Router port is set down, a link failure will not cause an alarm. This can be used to 
eliminate alarms from Router ports that are not in-use. When the Router port is set up, a link 
failure on the Ethernet port will cause an alarm to be reported to the Axxius 800.

Syntax:

set {rtr_lan-addr} {down|up}

Example:

set 2:1 down

The example will set the local LAN interface on slot 2 down.

{rtr_lan-addr}

The Router address is in the form {slot:port} or {slot "profile-name"}.

{down|up}

slot

Slot number (1-8) that contains the Router card.

port

Port number of the Router.

"profile-name"

The profile name for the Router interface. Name must be enclosed 
in quotes, with a maximum length of 11 characters. 

down

Set the Router as Out-of-Service. This command turns off the LED and 
disables alarm reporting for the Router specified. 

up

Set the Router as In-Service. This command turns on the LED and 
enables alarm reporting for the Router specified.

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

H3C SR8800 IM-FW-II Command Reference Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 107
3Com MSR 50 Series Safety Information Manual preview
MSR 50 Series
Brand: 3Com Pages: 12
H3C S9500 Series Operating Manual preview
S9500 Series
Brand: H3C Pages: 16
H3C H3C S3600 Series Datasheet preview
H3C S3600 Series
Brand: H3C Pages: 10
H3C MSR 930 Installation Manual preview
MSR 930
Brand: H3C Pages: 42
H3C MSR 800 Installation, Quick Start preview
MSR 800
Brand: H3C Pages: 2
H3C H3C S7500E Series Instruction Manual preview
H3C S7500E Series
Brand: H3C Pages: 34
H3C MSR Series Manual preview
MSR Series
Brand: H3C Pages: 33
H3C CR16000-F Configuration Manual preview
CR16000-F
Brand: H3C Pages: 14
H3C MSR 3600 Hardware Information And Specifications preview
MSR 3600
Brand: H3C Pages: 56
H3C H3C S7500E Series Configuration Manual preview
H3C S7500E Series
Brand: H3C Pages: 112
H3C S3100-52P Command Manual preview
S3100-52P
Brand: H3C Pages: 15
H3C SR8800 IM-FW-II Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 5
H3C H3C S7500E Series Installation Manual preview
H3C S7500E Series
Brand: H3C Pages: 50
H3C MSR810 Manual preview
MSR810
Brand: H3C Pages: 37
H3C CR16000-F Installation, Quick Start preview
CR16000-F
Brand: H3C Pages: 4
H3C MSR 20-1X Quick Start preview
MSR 20-1X
Brand: H3C Pages: 5
H3C RA10 Installation, Quick Start preview
RA10
Brand: H3C Pages: 4

Brands by name

Popular brands

Load more brands