manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

5-156

Axxius 800 - Release 2.2

CLI Commands

set

set (router-wan) ipx

Use the set (router-wan) ipx command to set the IPX traffic handling on the specified WAN 
interface.

Syntax:

set {rtr_card-addr} {"wan-name"} ipx {setting}

Example:

set 1 "LosAngeles" ipx bridge

The example will set the WAN interface named "LosAngeles" in slot 1, to 
bridge IPX.

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

{"wan-name"}

The WAN interface to modify. The name must be enclosed in quotes.

{setting}

block

Set the WAN to block IPX.

bridge

Set the WAN to bridge IPX with optimized local advertising IPX 
servers and networks.

optimize

Set the WAN to bridge IPX with optimized local advertising of 
IPX servers and networks.

Setting to optimize enables the Axxius to use Carrier Access’ 
network optimization feature, which ensures that only necessary 
data is transmitted over the WAN connection. The Axxius will 
initiate IPX learning mode. Learning mode is effective for 
optimizing bandwidth usage for IPX RIP, SAP, serialization and 
watchdog (IPX and SPX) packets. If you choose this option, the 
Axxius will initiate learning mode in order to gain knowledge of 
local and remote networks and services. Once it knows of remote 
networks and services, it can advertise the information on the local 
LAN on behalf of the remote networks and servers.

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
D-Link DSL-2740B Installation Manual preview
DSL-2740B
Brand: D-Link Pages: 10
Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Brand: Panasonic Pages: 2
Panasonic KX-UDS124 Maintenance Tool Manual preview
KX-UDS124
Brand: Panasonic Pages: 24
Panasonic i-Pro WV-SP302 Speci?Cations preview
i-Pro WV-SP302
Brand: Panasonic Pages: 2
Panasonic BB-HCM381A - Network Camera Troubleshooting Manual preview
BB-HCM381A - Network Camera
Brand: Panasonic Pages: 28
Panasonic BB-HCM381A - Network Camera Installation Manual preview
BB-HCM381A - Network Camera
Brand: Panasonic Pages: 2
Cabletron Systems Netlink FRX4000 Installation And Setup Manual preview
Netlink FRX4000
Brand: Cabletron Systems Pages: 8
Cabletron Systems 9C300-1 Upgrade Instructions preview
9C300-1
Brand: Cabletron Systems Pages: 4
Cabletron Systems MMAC-Plus 9F106-02 Reference Manual preview
MMAC-Plus 9F106-02
Brand: Cabletron Systems Pages: 7
Zonet ZFS3008 Installation Manual preview
ZFS3008
Brand: Zonet Pages: 8
OCCITALINA OXTOPUS EIA-709 User Manual preview
OXTOPUS EIA-709
Brand: OCCITALINA Pages: 54
MikroTik RouterBOARD SXT 5HnD Quick Setup Manual And Warranty Information preview
RouterBOARD SXT 5HnD
Brand: MikroTik Pages: 2
FOR-A MFR-16DTIO Installation Manual preview
MFR-16DTIO
Brand: FOR-A Pages: 2
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Brand: Enertronica Santerno Pages: 34
Ubiquiti EdgeRouter PRO Quick Start Manual preview
EdgeRouter PRO
Brand: Ubiquiti Pages: 20
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
Rajant Corporation BreadCrumb CX1 User Manual preview
BreadCrumb CX1
Brand: Rajant Corporation Pages: 40

Brands by name

Popular brands

Load more brands