Carrier Access Network Device Axxius 800 User Manual Download

Page: 278 / 568

5-178

Axxius 800 - Release 2.2

CLI Commands

show

show cclabels

The show cclabels

command displays all user defined DS0 cross-connect labels.

Syntax:

show cclabels

Example:

show cclabels

> show cclabels

Current DS0 Connection Labels:

---------- ---------- ---------- ---------- ----------

’label1’ ’label2’ ’label3’ ’label4’ ’V35label’

’test’

show clock

The show clock command displays the primary and secondary clocks.

Syntax:

show clock

Example:

show clock

This example will display the primary and secondary clock source.

> show clock

Primary Master Transmit Clock Source: Internal

Secondary Transmit Clock Source: Internal

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Network Device Axxius 800

Reviews:

Related manuals for Network Device Axxius 800

Brands by name

Popular brands

Carrier Access Network Device Axxius 800, User Manual

Search results

Summary of Contents for Network Device Axxius 800

Reviews:

Related manuals for Network Device Axxius 800

Brands by name

Popular brands