manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

5-230

Axxius 800 - Release 2.2

CLI Commands

status

status (bri) performance history

Use the status (bri) performance history command to display the performance statistics for 
the current 1 hour interval and all previous 1 hour intervals for the ISDN BRI card.

Syntax:

status {bri-addr} performance history

Example:

status 5:1 performance history

 

SLOT 5:

Performance Statistics for BRI Port 1:

                           HES    HSES      BE     DES    DSES

current interval             0       0       0       0       0

prev. interval 1             0       0       0       0       0

prev. interval 2             0                                

totals:                      0       0       0       0       0

elapsed time in current 1-hour interval: 00:37:38

completed 1-hour intervals in data:             2   

{bri-addr}

The BRI address, in the form {slot:port}.

status clock

Use the status clock command to display the current status of the primary and secondary clocks. 

Syntax:

status clock

Example:

status clock

Active Clock Source: Secondary

Primary:

  Clock Source:      Slot A DS1 1

  Clock Status:      Out of Service

Secondary:

  Clock Source:      Internal

  Clock Status:      In Service

slot

The slot number (1-8) that contains the BRI card

port

Port number, range or all

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

BandLuxe R500 Series User Manual preview
R500 Series
Brand: BandLuxe Pages: 67
Dahua NVR2104-S2 Quick Start Manual preview
NVR2104-S2
Brand: Dahua Pages: 6
Belkin F5D9001 Series Manual preview
F5D9001 Series
Brand: Belkin Pages: 72
Helmholz REX 200 Quick Start Manual preview
REX 200
Brand: Helmholz Pages: 28
Hornington AirStation WHR-G300N Settings preview
AirStation WHR-G300N
Brand: Hornington Pages: 6
Eaton APS6-400 Series Installation And Operation Manual preview
APS6-400 Series
Brand: Eaton Pages: 114
ZyXEL Communications ZyAIR G-3000H User Manual preview
ZyAIR G-3000H
Brand: ZyXEL Communications Pages: 299
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
3Com 3C589D User Manual preview
3C589D
Brand: 3Com Pages: 50
ZyXEL Communications GS1100-10HP User Manual preview
GS1100-10HP
Brand: ZyXEL Communications Pages: 30
ZyXEL Communications SHD1110 Quick Start Manual preview
SHD1110
Brand: ZyXEL Communications Pages: 12
Deliberant APC Mach 5 V3 Quick Installation Manual preview
APC Mach 5 V3
Brand: Deliberant Pages: 16
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34
Enterasys 2H258-17R Installation & User Manual preview
2H258-17R
Brand: Enterasys Pages: 62
Mobily NTC-40WV-QSG Quick Start Manual preview
NTC-40WV-QSG
Brand: Mobily Pages: 12
MikroTik wAP series User Manual preview
wAP series
Brand: MikroTik Pages: 5
National Instruments NI ELVIS III Getting Started preview
NI ELVIS III
Brand: National Instruments Pages: 37

Brands by name

Popular brands

Load more brands