manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

5-248

Axxius 800 - Release 2.2

CLI Commands

status

status (router) ip network table

Use the status (router) ip network table command to display the current table of learned 
IP Networks for the specified interface on the Router card.

Syntax:

status {rtr_card-addr} ip network table 

["profile-name"] 

Example:

status 5 ip network table

> status 5 ip network table

          ROUTER BLADE IP NETWORKS REPORT Slot-5

Total Entries-3 on 2 Ports

Display: <IP Networks >  Learned From: <All Ports   >

             Network         Subnet Mask     Metric Next Gateway    Port Name

   1. Static 200.1.1.0       255.255.255.0   1                      LosAngeles

   2. Static 100.0.0.0       255.0.0.0       1      192.136.43.52   Local LAN

   3. Direct 192.168.3.0     255.255.255.0   1      192.168.3.196   Local LAN

Example:

status 5 ip network table "Axxius50"

                                                                                

> status 5 ip network table "Axxius50"

          ROUTER BLADE IP NETWORKS REPORT Slot-5

Total Entries-2 on Local LAN

Display: <IP Networks >  Learned From: <Local LAN >

             Network         Subnet Mask     Metric Next Gateway    Frame

   1. Static 100.0.0.0       255.0.0.0       1      192.136.43.52   Eth II

   2. Direct 192.168.3.0     255.255.255.0   1      192.168.3.196   Eth II  

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

["profile-name"]

The profile name for the Router interface that is used to reach this destination. Name must 
be enclosed in quotes, with a maximum length of 11 characters. 

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

3Com TokenLink 3C359B Release Note preview
TokenLink 3C359B
Brand: 3Com Pages: 4
3Com TokenLink 3C359B Quick Start Manual preview
TokenLink 3C359B
Brand: 3Com Pages: 8
3Com TokenLink 3C339 Release Note preview
TokenLink 3C339
Brand: 3Com Pages: 2
3Com EtherLink 3C985B-SX Installation And User Manual preview
EtherLink 3C985B-SX
Brand: 3Com Pages: 44
3Com 3CR990 Administration Manual preview
3CR990
Brand: 3Com Pages: 88
3Com 3C16080 Important Information preview
3C16080
Brand: 3Com Pages: 2
3Com 3C905C-TX-M User Manual preview
3C905C-TX-M
Brand: 3Com Pages: 111
3Com TokenLink 3C359 Release Note preview
TokenLink 3C359
Brand: 3Com Pages: 4
3Com 3C421600A Quick Setup Manual preview
3C421600A
Brand: 3Com Pages: 74
3Com 3C421600A Installation Manual preview
3C421600A
Brand: 3Com Pages: 6
H3C SR8800 IM-FW-II Command Reference Manual preview
SR8800 IM-FW-II
Brand: H3C Pages: 107
3Com MSR 50 Series Safety Information Manual preview
MSR 50 Series
Brand: 3Com Pages: 12
H3C S9500 Series Operating Manual preview
S9500 Series
Brand: H3C Pages: 16
H3C H3C S3600 Series Datasheet preview
H3C S3600 Series
Brand: H3C Pages: 10
H3C MSR 930 Installation Manual preview
MSR 930
Brand: H3C Pages: 42
H3C MSR 800 Installation, Quick Start preview
MSR 800
Brand: H3C Pages: 2
H3C H3C S7500E Series Instruction Manual preview
H3C S7500E Series
Brand: H3C Pages: 34
H3C MSR Series Manual preview
MSR Series
Brand: H3C Pages: 33

Brands by name

Popular brands

Load more brands