manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

Axxius 800 - Release 2.2

5-249

CLI Commands

status

status (router) ipx network table

Use the status (router) ipx network table command to display the current table of learned 
IPX Networks for the specified interface on the Router card.

Syntax:

status {rtr_card-addr} ipx network table 

["profile-name"] 

Example:

status 5 ipx network table

> status 5 ipx network table

          ROUTER BLADE IPX NETWORKS REPORT Slot-5

Total Entries-4 on 1 Ports

Display: <IPX Networks>  Learned From: <All Ports   >

           Network  Hops Ticks  Next IPX Router    Port Name   Frame Type

   1. Static 00000011 2     4                         LosAngeles   802.3

   2. Static 00000011 2     4                         LosAngeles   802.2

   3. Static 00000011 2     4                         LosAngeles   SNAP

   4. Static 00000011 2     4                         LosAngeles   Eth II 

     

Example:

status 5 ipx network table "Axxius50"

                                                                                

> status 5 ipx network table "Axxius50"

          ROUTER BLADE IPX NETWORKS REPORT Slot-5

Total Entries-0 on Local LAN

Display: <IPX Networks>  Learned From: <Local LAN >

             Network  Hops Ticks  Next IPX Router    Frame Type

 No Records to Display... 

{rtr_card-addr}

The slot number (1-8) that contains the Router card.

["profile-name"]

The profile name for the Router interface that is used to reach this destination. Name must 
be enclosed in quotes, with a maximum length of 11 characters. 

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

H3C MSR 20-20 Supplementary Manual preview
MSR 20-20
Brand: H3C Pages: 6
3Com OfficeConnect 3CP4144 How To Set Up preview
OfficeConnect 3CP4144
Brand: 3Com Pages: 4
3Com OfficeConnect 3CP4144 Release Note preview
OfficeConnect 3CP4144
Brand: 3Com Pages: 2
H3C MSR 20-20 User Manual preview
MSR 20-20
Brand: H3C Pages: 60
H3C MSR 20 Series Manual preview
MSR 20 Series
Brand: H3C Pages: 149
3Com 3C13636 Installation Manual preview
3C13636
Brand: 3Com Pages: 27
Cambium Networks PTP 820 Series Manual preview
PTP 820 Series
Brand: Cambium Networks Pages: 29
CSS SafetyNet Quick Install Manual preview
SafetyNet
Brand: CSS Pages: 2
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Brand: NetComm Pages: 3
IBM J02M Quick Start Manual preview
J02M
Brand: IBM Pages: 32
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Brand: Jetter Pages: 67
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Paradyne Hotwire 6341 Installation Instructions Manual preview
Hotwire 6341
Brand: Paradyne Pages: 23
Draytek Vigor 2760 Series Quick Start Manual preview
Vigor 2760 Series
Brand: Draytek Pages: 54
Network Critical SmartNA-X User Manual preview
SmartNA-X
Brand: Network Critical Pages: 200
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
TP-Link TD-W8101G Quick Installation Manual preview
TD-W8101G
Brand: TP-Link Pages: 16
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16

Brands by name

Popular brands

Load more brands