manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

7-8

Axxius 800 - Release 2.2

DS3 Controller Card

Controller and DS3 Redundancy

Controller and DS3 Redundancy

Protection Modes

The Axxius 800 can be provisioned with one or two DS3 Controller cards and 
connections to one or two DS3 lines, which will provide the following levels of 
protection:

l

Electronics Protection – when provisioned with two Controller cards and only 
one DS3 line, only the Controller cards can be protected

l

Network Protection – when provisioned with one Controller and two 
independent DS3 lines, only the DS3 lines can be protected.

l

Electronics and Network Protection – when provisioned with two Controller 
cards and two independent DS3 lines, both the controller cards and the DS3 lines 
can be protected

Electronics Protection Mode

In this mode there are two DS3 Controllers installed the Axxius 800, but only one DS3 
line connected. 

The electronics mode of protection provides Controller card redundancy. Because there 
is only one DS3 connected, there is no DS3 redundancy. The receive path from the DS3 
line is simultaneously applied to the receiver of both Controller cards (see Figure). This 
enables both controllers to monitor the condition of the DS3 line so both are 
continuously framed up to the incoming signal. The Controller-select signal disables 
the outputs of the low-speed receive paths on the standby Controller and enables the 
low-speed receive paths on the active controller. The active Controller’s transmit signal 
is connected to the transmit path of the DS3 line through a relay, while the standby is 
disconnected until a protection switch occurs.

The automatic redundancy mode is used to enable and disable protection switching. If 
the redundancy control process determines the active controller is malfunctioning, or a 
maintenance switch is invoked (the switch command), a protection switch will occur. 
This means that the active Controller relinquishes control to the secondary Controller. 
This is done by enabling the standby Controller’s receive path and disabling the 
originally active Controller’s low-speed receive path (Controller-select signal) and 

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Makita 3606 Parts Breakdown preview
3606
Brand: Makita Pages: 2
Panasonic BL-C20 Troubleshooting Manual preview
BL-C20
Brand: Panasonic Pages: 18
Patton electronics SMARTNODE 4900 Getting Started Manual preview
SMARTNODE 4900
Brand: Patton electronics Pages: 75
Patton electronics RocketLink-G 3088/I Getting Started Manual preview
RocketLink-G 3088/I
Brand: Patton electronics Pages: 61
Patton SmartNode 5200 Quick Start Manual preview
SmartNode 5200
Brand: Patton Pages: 12
Patton SL4020 Getting Started Manual preview
SL4020
Brand: Patton Pages: 84
Patton OnSite 3210 Series User Manual preview
OnSite 3210 Series
Brand: Patton Pages: 110
Patton electronics 4900 Series Specification Sheet preview
4900 Series
Brand: Patton electronics Pages: 2
Patton electronics SMARTNODE 4110 Series User Manual preview
SMARTNODE 4110 Series
Brand: Patton electronics Pages: 78
Patton electronics SMARTNODE 4552 Quick Start Manual preview
SMARTNODE 4552
Brand: Patton electronics Pages: 8
Netis DL4305D Quick Installation Manual preview
DL4305D
Brand: Netis Pages: 16
eWON 2101CD Installation Manual preview
2101CD
Brand: eWON Pages: 34
IndigoVision Compact NVR-AS 4000 User Manual preview
Compact NVR-AS 4000
Brand: IndigoVision Pages: 38
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Brand: Dahua Pages: 452
ADTRAN NetVanta Analog Modem Dial Backup Interface Module Quick Start Manual preview
NetVanta Analog Modem Dial Backup Interface Module
Brand: ADTRAN Pages: 2
Amer.com 8-Port 10/100Mbps Fast Ethernet Switch User Manual preview
8-Port 10/100Mbps Fast Ethernet Switch
Brand: Amer.com Pages: 14
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Brand: Genexis Pages: 7
Teltonika RUT955 User Manual preview
RUT955
Brand: Teltonika Pages: 12

Brands by name

Popular brands

Load more brands