Carrier Access Network Device Axxius 800 User Manual Download

Page: 417 / 568

Axxius 800 - Release 2.2

11-3

Single Channel POTS Cards

Technical Specifications

Technical Specifications

Controller Software Required

Release 1.0 or higher is required for the POTS Service cards

FXS Transmission Performance

Return Loss: ERL > 28 dB, SRL > 20 dB with respect to 900

Ω + 2.16µ

Transhybrid Loss: ERL > 28 dB, SRL > 20 dB with respect to 900

Ω + 2.16µ

Idle Noise: A/D < 25 dBrnC0

Signal/Distortion: > 45 dB with 1004 Hz, 0 dBm0 input

Terminating Impedance: 900

Ω

2.16µ

Transmit Gain/Loss: +4 to -12 dB (in .25 increments)

Receive Gain/Loss: +4 to -12 dB (in .25 increments)

Overload: +3.0 dBm0

Frequency Response: +0 dB -1.0 dB from 300 to 3400 Hz

Longitudinal Balance: >50 dB

Modem support: full compatibility with V.90 modems

Modem Performance

The Single Channel POTS card modem is registered for direct connection to the
PSTN

FXS Signaling Performance

DC Loop Range: 512

Ω

Loop Feed: Nominal -48 VDC with 26mA current limit

Ringing Voltage: 40 V rms, 20 Hz

Maximum Ringers: 2 REN, FCC Class B ringers

FXS Signaling: FXS loop start

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Network Device Axxius 800

Reviews:

Related manuals for Network Device Axxius 800

Brands by name

Popular brands

Carrier Access Network Device Axxius 800, User Manual

Search results

Summary of Contents for Network Device Axxius 800

Reviews:

Related manuals for Network Device Axxius 800

Brands by name

Popular brands