Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 419 / 568

background image

Axxius 800 - Release 2.2

11-5

Single Channel POTS Cards

Built-In Card Handles

Built-In Card Handles

The Single Channel POTS cards are designed with a handle built into the faceplate to
assist in the removal of the card from the chassis. This handle slides out away from the
unit, creating a handle for a more effective grip.

Card Configuration

The Single Channel POTS card can be configured, using CLI commands.

CLI Commands

The following commands are used to configure the POTS cards. For detailed
information on these commands, see Chapter 5, CLI Commands.

l

connect
Creates two-way connections between channels

l

disconnect
Removes a connection created by the connect command

l

set (fxsPS or fxsPSM)
To setup the voice channels parameters (rx gain, signal, tx gain).

l

show (fxsPS or fxsPSM)
Displays the settings (type, signaling, rx gain, tx gain) for the FXS PS cards.

l

status (fxsPS or fxsPSM)
Displays the status (AB bits received, AB bits transmitted, signal, T1
activity, trunk processing) of the specified FXS PS cards.

«
...
417
418
419
420
421
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Brand: N-Tron Pages: 101

Brand: Aastra Pages: 2

Brand: LaCie Pages: 4

Brand: LaCie Pages: 4

RUGGEDSWITCH RS900G

Brand: RuggedCom Pages: 23

Brand: E-Lins Pages: 9

Brand: ZyXEL Communications Pages: 2

Brand: SMC Networks Pages: 56

Brand: CAME Pages: 32

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Bolide BN-NVR/NX

Brand: GSA Pages: 101

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: LevelOne Pages: 142

Brand: ORiNG Pages: 101

Sporlan Division SCS-PB Series

Brand: Parker Pages: 10

Brand: ActionTec Pages: 87

OmniSwitch 6624

Brand: Alcatel Pages: 546

Brand: netsys Pages: 243

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands