manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

Axxius 800 - Release 2.2

17-3

Low Speed Protection Card

Overview

The Backup Card

A Quad T1 or Quad DS1 ADPCM service card can be configured as the “Backup card”. 
The Backup card provides T1 port protection for other installed T1 service cards, and 
can occupy any one of the eight service card slots. 

Note: It is imperative that the slot designated for the backup card have NO wire-
wrap connections.

Protected Cards

The Quad T1/Quad DS1 ADPCM service cards to be protected can occupy any of the 
7 remaining service card slots (backup card occupies the 8th slot). One or all four ports 
can be protected, though each series of ports (all 1s, 2s, 3s and port 4s) have one backup 
T1 port. The Axxius system can use other service cards in any of the 8 service card slots 
without interference with the Low Speed Protection system.

Port Backup and Prioritization:

Priorities can be set for these protected ports (1-7) where 1 is the highest priority and 
the default setting is 7. If more than 1 fault occurs at the same time the port with the 
higher priority is granted the protection. In cases where traffic from a lower priority 
port is already switched to backup, the traffic is forced back to the failed port to provide 
the higher priority traffic with the backup port. When port protection requests are set at 
the same level, protection is granted on a "first come, first serve" basis.

Above port #1 of the backup card provides a single T1 backup to all the protected T1’s, 
port #1 in the system. This scenario is the same for the Backup port #2, port #3, and 
port #4.

Re

lay C

ard

     T1 Protected Cards

Bac

kup

 Ca

rd

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Magnat Audio MC 200 Faq preview
MC 200
Brand: Magnat Audio Pages: 2
Abocom MH200 Quick Installation Manual preview
MH200
Brand: Abocom Pages: 11
Abocom CWB1000 Quick Installation Manual preview
CWB1000
Brand: Abocom Pages: 19
Watchguard Firebox T15 Quick Start Manual preview
Firebox T15
Brand: Watchguard Pages: 39
Planet ADSL 2/2+ Router with USB Port ADE-3410v2 User Manual preview
ADSL 2/2+ Router with USB Port ADE-3410v2
Brand: Planet Pages: 62
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
Eicon Networks Diva 2440 Quick Start Manual preview
Diva 2440
Brand: Eicon Networks Pages: 32
BHU NETWORKS BXM2 User Manual preview
BXM2
Brand: BHU NETWORKS Pages: 75
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
Airlinkplus ASW224 User Manual preview
ASW224
Brand: Airlinkplus Pages: 20
ZyXEL Communications SHD1110 Quick Start Manual preview
SHD1110
Brand: ZyXEL Communications Pages: 12
Zhone ETHX-2214-DS3 Installation Instructions Manual preview
ETHX-2214-DS3
Brand: Zhone Pages: 28
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
Digisol DG-SR2004 User Manual preview
DG-SR2004
Brand: Digisol Pages: 73
B&B Electronics ZXT9-IO-222R2 Product Manual preview
ZXT9-IO-222R2
Brand: B&B Electronics Pages: 74
Divio NRM 311 User Manual preview
NRM 311
Brand: Divio Pages: 78
Farallon Ethernet ISA Card User Manual preview
Ethernet ISA Card
Brand: Farallon Pages: 20
Crestron DigitalMedia DM-RPP-K24 Manual preview
DigitalMedia DM-RPP-K24
Brand: Crestron Pages: 2

Brands by name

Popular brands

Load more brands