Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 487 / 568

background image

Axxius 800 - Release 2.2

17-7

Low Speed Protection Card

Card Configuration

Use the following steps to set up a Protected System.

1. Install a Relay card in the Axxius Relay slot.

2. Set the jumpers on the Quad T1 cards to route the signal to the wire-wrap pins,

see Jumper Settings on page 14-8 for detailed instructions.

3. Prewire the chassis for Quad T1 cards (wire-wrap pins).

Note: It is imperative that the slot designated for the Quad T1 backup
card have NO wire-wrap connections.

4. Install the Backup Quad T1 card into the designated service card slot (no

prewire).

5. Install Quad T1 cards that are to be protected into the prewired card slots.

Note: These QT1 cards can be in any slot, as well as other card types. Also
removal and/or replacement of any of these service cards will not effect
service to cards in adjacent slots.

Perform the following CLI commands to configure the system for protection.

With the above steps protection is now provided for the specified cards. Any
single protected card can be pulled from its slot with only minimal interruption
to service. Since protection is on a 1xN basis once protection is provided for a
failed port other ports cannot be protected at the same time.

Command

Description

set lsbackup {t1_card-addr}

This command defines the backup slot (can
be any slot)

set lsprotect enable

To enable the Low Speed Protection option

set lsprotect {slot:port}

{revertive|nonrevertive}

[priority] [1-7]

This command defines the protected cards.
Set all ports to revertive or non-revertive as
necessary with an optional priority level

show lsprotect

To display the current settings

status lsprotect

To display the current status

«
...
485
486
487
488
489
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Brand: D-Link Pages: 15

Brand: D-Link Pages: 2

Brand: Panasonic Pages: 2

Brand: H3C Pages: 6

OfficeConnect 3CP4144

Brand: 3Com Pages: 4

OfficeConnect 3CP4144

Brand: 3Com Pages: 2

Brand: H3C Pages: 60

Brand: H3C Pages: 149

Brand: 3Com Pages: 27

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

Brand: Lanner Pages: 109

Brand: Stephen Pages: 102

Brand: ADIC Pages: 140

Brand: ZyXEL Communications Pages: 2

Ethernet MCA 10/100 Adapter

Brand: Olicom Pages: 88

Brand: NetCommWireless Pages: 28

Brand: Linksys Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands