manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

Glossary - 2

Axxius 800 - Release 2.2

Glossary

authorization

authorization

The process of granting or denying access to a network resource. Most 
computer security systems are based on a two-step process, sometimes 
more. The first stage is authentication, which ensures that a user is who 
he or she claims to be and in some cases, that the user is not already on 
the system. The second stage is authorization, which allows the user 
access in varied degrees to various resources based on the preassigned 
privileges associated with the user’s identity.

B-channel

Short for Bearer-channel, the main data channel in an ISDN connection. 
Basic Rate ISDN (BRI) service consists of two 64 Kbps B-channels, and 
one D-channel for transmitting control information. 

B8ZS

Bipolar 8-Zero Substitution, a coding scheme that maintains ones 
density.

backplane

A common bus at the rear of the computer chassis connecting each circuit 
card slot to the other parts of the system. Motherboards on modern PCs 
are a general equivalent. It also distributes low-voltage AC and DC, 
filtered and un-filtered power to each slot.

bandwidth

The amount of data that can travel through a channel in a given period of 
time. Bandwidth is usually measured in cycles per second (hertz) or in 
bits per second (BPS). The larger the bandwidth, the more information 
the network can handle. ISDN is usually 64KB, 128KB or 256KB. 
ASDL and DSL are generally faster than ISDN and sometimes faster 
than cable. Cable connections are usually 500KB or 1MB. T1 is 1.5MB 
and T3 is 45MB.

Basic Rate 
Interface (BRI)

Basic Rate Interface is an Integrated Services Digital Network (ISDN) 
interface typically used by smaller sites and customers. This interface 
consists of a single 16 Kbps Data (or "D") channel plus 2 Bearer (or "B") 
channels for voice and/or data.

BER

Bit Error Rate, the number of erred bits divided by the total number of 
bits.

BERT

Bit Error Rate Tester

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
XAVI Technologies Corp. 7721r User Manual preview
7721r
Brand: XAVI Technologies Corp. Pages: 71
Texas Instruments ThunderLAN TNETE100A Programmer'S Manual preview
ThunderLAN TNETE100A
Brand: Texas Instruments Pages: 179
Tripp Lite N201-005-BL Specification Sheet preview
N201-005-BL
Brand: Tripp Lite Pages: 3
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Conel UR5i v2 SL User Manual preview
UR5i v2 SL
Brand: Conel Pages: 32
ADIC FCR 200 Operator'S Manual preview
FCR 200
Brand: ADIC Pages: 140
Cyclades AlterPath Manager 2500 Installation, Configuration And User Manual preview
AlterPath Manager 2500
Brand: Cyclades Pages: 368
Dahua Technology NVR2104/2108HS-W-4KS2 1U User Manual preview
NVR2104/2108HS-W-4KS2 1U
Brand: Dahua Technology Pages: 363
Digisol DG-SR2004 User Manual preview
DG-SR2004
Brand: Digisol Pages: 73
Comtrend Corporation CT-510 User Manual preview
CT-510
Brand: Comtrend Corporation Pages: 69
Accusys ACD-76300 Quick Installation Manual preview
ACD-76300
Brand: Accusys Pages: 12
Paradyne FrameSaver DSL 9783 CSU/DSU User Manual preview
FrameSaver DSL 9783 CSU/DSU
Brand: Paradyne Pages: 233
Linksys HPES03 User Manual preview
HPES03
Brand: Linksys Pages: 17
HP AD331A Manual preview
AD331A
Brand: HP Pages: 10
HP A6825A Performance Manual preview
A6825A
Brand: HP Pages: 11
HP AB290A Installation Manual preview
AB290A
Brand: HP Pages: 18

Brands by name

Popular brands

Load more brands