Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 539 / 568

background image

Axxius 800 - Release 2.2

Glossary - 7

Glossary

DHCP

DHCP

Dynamic Host Configuration Protocol. DHCP is a network configuration
that allows maintenance to be performed from a central site rather than
by end users.

download

To transfer data from a larger "host" system to a smaller "client" system’s
hard drive or other local storage device.

Drop & Insert
(D&I)

As applied to T1, D&I refers to the process whereby one DS0 channel is
demultiplexed out of the DS1 synchronous bit stream at one port of a
digital channel back and another DS0 inserted back in.

DS0

Digital Signal Zero, the standard bandwidth for digitized voice channels.

DS1

Digital Signal Level 1. A digital signal transmitted at a nominal rate of
1.544 Mbps.

DS3

Digital Signal Level 3. A digital signal transmitted at a nominal rate of
44.736 Mbps.

DSU/CSU

Data Service Unit/Channel Service Unit. A device terminating a digital
channel on a customer’s premises where it performs line coding, line
conditioning and equalization functions while responding to the receipt
of loopback codes sent from the Central Office (CO) A DSU/CSU sits
between the digital line coming in from the CO and devices such as
channel banks or data communications devices.

Dual Tone
Multi-
Frequency
(DTMF)

Dual Tone Multi-Frequency is the system used by touch-tone telephones.
DTMF assigns a specific sound frequency, or tone, to each key so that it
can easily be identified by a monitoring microprocessor. That frequency
is then translated into a usable analog or digital signal. This is commonly
known as Touch Tone.

Dynamic Host
Configuration
Protocol
(DHCP)

A network configuration that allows maintenance to be performed from
a central site rather than by end users.

«
...
537
538
539
540
541
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Brand: 3Com Pages: 20

ROADRECORDER 8000

Brand: Safety Vision Pages: 40

Brand: QNAP Pages: 54

Brand: Softing Pages: 16

Brand: 8e6 Technologies Pages: 94

Brand: ExtraHop Pages: 3

Brand: NetCommWireless Pages: 28

Brand: ZyXEL Communications Pages: 4

Cyclades CS4008

Brand: Avocent Pages: 2

Brand: Orcon Pages: 2

Brand: CTC Union Pages: 12

Brand: Ultra Pages: 4

Brand: WEIGL Pages: 6

Network Expansion Port 2

Brand: Navico Pages: 17

Brand: NetComm Pages: 124

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 2

Brand: Johnson Controls Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands