Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 541 / 568

background image

Axxius 800 - Release 2.2

Glossary - 9

Glossary

frame

frame

A fragment of data that is packaged into a frame format, which comprises
a header, payload, and trailer.

frame relay

A packet-switching protocol for connecting devices on a Wide Area
Network (WAN). Frame Relay networks in the U.S. support data transfer
rates at T1 (1.544 Mbps) and T3 (45 Mbps) speeds. Most telephone
companies now provide Frame Relay service for customers who want
connections at 56 Kbps to T1 speeds. However, it is being replaced in
some areas by faster technologies, such as ATM.

FX

Foreign Exchange. A Central Office trunk which has access to a distant
central office. Dial Tone is returned from that distant Central Office, and
a location can be reached in the area of the foreign Central Office by
dialing a local number. This will provide easier access for customers in
that area and calls may be made anywhere in the foreign exchange area
for a flat rate.

FXO

Foreign Exchange Office. Foreign exchange (FX) service is a service
that can be ordered from the telephone company that provides local
telephone service from a central office which is outside (foreign to) the
subscriber’s exchange area. Simply, a user can pick up the phone in one
city and receive a dial tone in the foreign city. This kind of connection is
provided by a type of trunk called foreign exchange (FX) trunk. FX trunk
signaling can be provided over analog or T1 links. Connecting POTS
telephones to a computer telephony system via T1 links requires a
channel bank configured with FX type connections.

FXS

Foreign Exchange Station.

gateway

A link from one computer system to a different computer system.

ground

A physical connection to the earth or other reference point.

ground start
(GS)

A method of signaling from a terminal or subscriber loop to a switch, in
which method one side of a cable pair is temporarily grounded

«
...
539
540
541
542
543
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Brand: D-Link Pages: 10

Brand: F-SECURE Pages: 19

Brand: Idis Pages: 123

Brand: Idis Pages: 29

Brand: Idis Pages: 28

DirectIP DR-1304P

Brand: Idis Pages: 82

Brand: iDirect Pages: 130

Brand: Planet Pages: 20

Brand: Oracle Pages: 112

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

PCH1 T P Series

Brand: Parker Pages: 107

Brand: Idis Pages: 22

Brand: Chase Research Pages: 114

Brand: Zhone Pages: 53

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Brand: 3Com Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands