Carrier Access Network Device Axxius 800 User Manual Download | Manualshive

Page: 544 / 568

background image

Glossary - 12

Axxius 800 - Release 2.2

Glossary

Line Coding Violation (LCV)

Line Coding
Violation
(LCV)

This parameter is a count of both BPVs and EXZs occurring over the
accumulation period. An EXZ increments the LCV by one regardless of
the length of the zero string.

Line Errored
Seconds (LES)

A Line Errored Second is a second in which one or more CVs occurred
OR one or more LOS defects.

Line Interface
Unit (LIU)

Typically, a controller device in a D-type channel bank, that incorporates
a controller, channel service unit (CSU), ringing generator and power
converter on a single card to interface between the T1 network and the
analog functions of the channel bank.

LLC

Logical Link Control. A protocol developed by the IEEE 802.2
committee for data-link-level transmission control

LMI

Local Management Interface. A specification for the use of frame-relay
products that define a method of exchanging status information between
devices such as routers.

LMU

Line Monitor Unit.

LOF

Loss of Frame.

LOS

Los of Signal.

loop back test

Any test in which a test signal is injected at one end of a circuit, is looped
back at the other end, and monitored at the originating end.

loop start (LS)

A method of demanding dial tone from the central office by completing
an electrical pathway between the outbound and return conductors of a
telephone line. Loop start is employed by single-line telephone
instruments, for example

loopback

A diagnostic test in which a signal is transmitted across a medium while
the sending device waits for its return.

«
...
542
543
544
545
546
...
»

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

TotalStorage SAN16M-R SAN

Brand: IBM Pages: 116

Adapter Bracket

Brand: Paradyne Pages: 1

RIPWAVE 40-00460-00R

Brand: Navini Networks Pages: 35

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: QNAP Pages: 54

Brand: TRENDnet Pages: 10

Brand: axing Pages: 52

Media Board D/120JCT-LS-EW

Brand: Dialogic Pages: 2

McDATA Eclipse 1620

Brand: Sun Microsystems Pages: 9

Brand: ZyXEL Communications Pages: 2

ACC-BKT-AX-BEAM

Brand: Extreme Networks Pages: 35

ROADRECORDER 8400 NVR

Brand: Safety Vision Pages: 27

USB device 622x

Brand: National Instruments Pages: 23

Brand: Moxa Technologies Pages: 94

Brand: Zte Pages: 32

Brand: Cambium Networks Pages: 672

Brand: Digi Pages: 1113

Brand: Allied Telesis Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands