manualshive.com logo in svg

Carrier Access Network Device Axxius 800, User Manual

The Axxius 800, an innovative Carrier Access Network Device, offers seamless connectivity and efficient data transmission. Enhance your user experience by easily accessing the comprehensive User Manual, available for free download from our website. Discover the full potential of this remarkable product and optimize your networking capabilities today.

Share
Download
background image

Axxius 800 - Release 2.2

ix

 Preface

Warranty

Warranty

Carrier Access Corporation conditionally warrants to BUYER that PRODUCTS are free from substantial 
defect in material and workmanship under normal use given proper installation and maintenance for the 
period of five years from the date of shipment by Carrier Access Corporation.

BUYER will promptly notify Carrier Access Corporation of any defect in the PRODUCT. Carrier Access 
Corporation or its agent will have the right to inspect the PRODUCT or workmanship on BUYER’S or 
BUYER’S customer premises. Carrier Access Corporation has the option to: (a) repair, replace or service 
at its factory or on the premises the PRODUCT or workmanship found to be defective; or (b) credit 
BUYER for the 

PRODUCT

 in accordance with Carrier Access Corporation’s depreciation policy. 

Refurbished material may be used to repair or replace the PRODUCT. PRODUCTS returned to Carrier 
Access Corporation for repair, replacement, or credit will be shipped prepaid to BUYER.

Limitations of Warranty & Limitation of Remedies

Correction of defects by repair, replacement, service or credit will be at Carrier Access Corporation’s 
option and constitute fulfillment of all obligations to buyer for breach of warranty.

Carrier Access Corporation assumes no warranty liability with respect to defects in the PRODUCT caused 
by: (a) modification, repair, installation, operation or maintenance of the PRODUCT by anyone other than 
Carrier Access Corporation or its agent, except as described in Carrier Access Corporation’s 
documentation; or (b) the negligent or other improper use of the PRODUCT; or (c) handling or 
transportation after title of the PRODUCT passes to BUYER.

Other manufacturer’s equipment purchased by Carrier Access Corporation and resold to BUYER will be 
limited to that manufacture’s warranty. Carrier Access Corporation assumes no warranty liability for other 
manufacturer’s equipment furnished by BUYER.

Buyer understands and agrees as follows: the warranties in this agreement replace all other warranties, 
expressed or implied, and all other obligations or liabilities of Carrier Access Corporation, including any 
warranties of merchantability and fitness for a particular purpose. All other warranties are disclaimed and 
excluded by Carrier Access Corporation.

The remedies contained in this agreement will be the sole and exclusive remedies whether in contract, tort 
or otherwise, and Carrier Access Corporation will not be liable for injuries or damages to persons or 
property resulting from any case whatsoever, with the exception of injuries or damages caused by the gross 
negligence of Carrier Access Corporation. These limitations apply to all services, software, and products 
during and after the warranty period. In no event will Carrier Access Corporation be liable for any special, 
incidental, or consequential damages or commercial losses even if Carrier Access Corporation has been 
advised thereof.

No agent, distributor, or representative is authorized to make any warranties on behalf of Carrier Access 
Corporation or to assume for Carrier Access Corporation any other liability in connection with any of 
Carrier Access Corporation’s PRODUCTS, Software, or Services.

Summary of Contents for Network Device Axxius 800

























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Network Device Axxius 800

Abocom MH200 Quick Installation Manual preview
MH200
Brand: Abocom Pages: 11
Abocom CWB1000 Quick Installation Manual preview
CWB1000
Brand: Abocom Pages: 19
ICP DAS USA I-7532M-FD User Manual preview
I-7532M-FD
Brand: ICP DAS USA Pages: 48
ICP DAS USA WF-2572 User Manual preview
WF-2572
Brand: ICP DAS USA Pages: 24
ICP DAS USA MSM-508 Quick Start preview
MSM-508
Brand: ICP DAS USA Pages: 4
Quick Eagle Networks 5842 Specification Sheet preview
5842
Brand: Quick Eagle Networks Pages: 4
National Instruments NI 9265 Operating Instructions Manual preview
NI 9265
Brand: National Instruments Pages: 26
National Instruments NI 9203 User Manual And Specifications preview
NI 9203
Brand: National Instruments Pages: 85
National Instruments Module SCXI-1503 User Manual preview
Module SCXI-1503
Brand: National Instruments Pages: 79
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
EnGenius ETR9360 Quick Start Manual preview
ETR9360
Brand: EnGenius Pages: 3
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
Enterasys Enterasys Matrix 2G4082-25 Hardware Installation Manual preview
Enterasys Matrix 2G4082-25
Brand: Enterasys Pages: 58
Axis P1355-E User Manual preview
P1355-E
Brand: Axis Pages: 64
SHOWTEC LED Operator 4 Manual preview
LED Operator 4
Brand: SHOWTEC Pages: 15
Billion BIPAC 7100G Quick Start Manual preview
BIPAC 7100G
Brand: Billion Pages: 14
Patton electronics 3196RC User Manual preview
3196RC
Brand: Patton electronics Pages: 93
Panduit CDPP8RG-S Installation Instructions preview
CDPP8RG-S
Brand: Panduit Pages: 5

Brands by name

Popular brands

Load more brands