background image

 

2

 

 

The machine room shall be finished with 
waterproof floor 

 
The machine room shall be finished 
with waterproof floor to protect 
surrounding equipments and facilities 
from wetting

Ventilate the machine room whenever 
nitrogen pressurized test is performed 

 
Fully ventilate the machine room 
whenever nitrogen pressurized test is 
performed on the unit or piping. 
Insufficient ventilation may cause an 
oxygen-deficient accident.

 

Make space around the unit for safe 
maintenance work

 

 

Make space around the unit for safe 
maintenance work.   
Lack of space may cause deficient 
service works and an injury in case.

 

Earth leakage breaker shall be installed   

 

Earth leakage breaker shall be 
installed in some installation locations 
to prevent a shock accident.

   

Perform grounding works 

 
Grounding works is necessary but 
never connect the earth wire to the 
gas piping, water piping and/or earth 
line of the lightning rod or telephone. 
Imperfect grounding may damage the 
unit or cause a shock.

 

Wires shall be securely connected 

 
Wires shall be securely connected and 
the terminal connection shall be 
stress-free from any external force. 
Defective connection may cause heat 
generation or fire.

 

Flue and the unit shall be insulated by 
professionals 

 
Flue and the unit shall be insulated by 
professionals. 
Insufficient insulation may cause a fire 
or a burn injury.

 

 

 
 

NOTE) 
(1)  Absorption chiller is indoor use only. 
(2)  IP number of Absorption chiller is IP40. 
(3)  Install Absorption chiller at a height of less than 1000m above sea level. If the location is higher than 

1000m above sea level, please contact a service agent. 
 

CAUTION

 

Must be 

observed

Must be 

observed

Must be 

observed

Must be 

observed

Must be 

observed

Must be 

observed

Must be 

observed

Summary of Contents for 16LJ-F Series












Reviews: