Carrier 30XW Installation, Operation And Maintenance Instructions Download

Page: 30 / 36

12 - OPTIONS

Options

No.

Description

Advantages

Use for 30XW

range

Medium-temperature brine

solution

Implementation of new control algorithms and redesigned

evaporator to allow chilled brine solution production down to -6°C

when ethylene glycol is used (-3°C with propylene glycol)

Covers specific applications such as ice storage and

industrial processes

Only sizes

512/562/1012/1154

Low-temperature brine solution

Implementation of new control algorithms and redesigned

evaporator to allow chilled brine solution production down to -12°C

when ethylene glycol is used (-8°C with propylene glycol)

Covers specific applications such as ice storage and

industrial processes

Only sizes

512/562/1012/1154

Light-brine solution, down to

-3°C

Implementation of new control algorithms and redesigned

evaporator to allow chilled brine solution production down to -3°C

when ethylene glycol is used (0°C with propylene glycol)

Matches with most application requirements for

ground-sourced heat pumps and fits with many

industrial processes requirements

254-1762

Unit supplied in two assembled

parts

The unit is equipped with flanges that allow disassembly of the unit

on site

Facilitates installation in plant rooms with limited access Only sizes

1612/1652/1702/1762

Master/slave operation

Unit equipped with supplementary water outlet temperature sensor

kit (to be field installed) allowing master/slave operation of two

units connected in parallel

Optimised operation of two units connected in parrallel

operation with operating time equalisation

254-1762

Single power connection point

Unit power connection via one main supply connection

Quick and easy installation

1002-1762

No disconnect switch

82A

Unit without disconnect switch, but with short-circuit protection

device

Permits an external electrical disconnect system for the

unit (field-supplied), while ensuring unit short circuit

protection

254-1762

Evap. single pump power/control

circuit

Unit equipped with an electrical power and control circuit for one

pump evaporator side

Quick and easy installation: the control of fixed speed

pumps is embedded in the unit control

254-1252, 1314

Evap. dual pumps power/control

circuit

84D

Unit equipped with an electrical power and control circuit for two

pumps evaporator side

Quick and easy installation: the control of fixed speed

pumps is embedded in the unit control

254-1252, 1314

Cond. single pump power/control

circuit

84R

Unit equipped with an electrical power and control circuit for one

pump condenser side

Quick and easy installation: the control of fixed speed

pumps is embedded in the unit control

254-1252, 1314

Condenser insulation

Thermal condenser insulation

Minimizes thermal dispersions condenser side (key

option for heat pump or heat recovery applications)

254-1762

Service valve set

Liquid line valve (evaporator inlet) and compressor suction line

valve

Allow isolation of various refrigerant circuit components

for simplified service and maintenance

254-1762

Evaporator with one pass less

100C

Evaporator with one pass on the water side. Evaporator inlet and

outlet on opposite sides.

Easy to install, depending on site. Reduced pressure

drops

254-1762

Condenser with one pass less

102C

Condenser with one pass on the water side. Condenser inlet and

outlet on opposite sides.

Easy to install, depending on site. Reduced pressure

drops

254-1762

21 bar evaporator

104

Reinforced evaporator for extension of the maximum water-side

service pressure to 21 bar (standard 10 bar)

Covers applications with a high water column evaporator

side (typically high buildings)

254-1762

21 bar condenser

104A Reinforced condenser for extension of the maximum water-side

service pressure to 21 bar (standard 10 bar)

Covers applications with a high water column condenser

side (typically high buildings)

254-1762

Reversed evaporator water

connections

107

Evaporator with reversed water inlet/outlet

Easy installation on sites with specific requirements

254-1762

Reversed condenser water

connections

107A

Condenser with reversed water inlet/outlet

Easy installation on sites with specific requirements

254-1762

J-Bus gateway

148B

Bi-directional communication board complying with JBus protocol Connects the unit by communication bus to a building

management system

254-1762

Lon gateway

148D

Bi-directional communication board complying with Lon Talk

protocol

Connects the unit by communication bus to a building

management system

254-1762

Bacnet over IP

149

Bi-directional high-speed communication using BACnet protocol

over Ethernet network (IP)

Easy and high-speed connection by ethernet line to a

building management system. Allows access to multiple

unit parameters

254-1762

High condensing temperature

150

Optimized compressor for operation at high condensing

temperature

Increased condenser leaving water temperature up to

63°C. Allows applications with high condensing

temperature (heat pumps, installations with not

generously sized dry-coolers or more generally,

installations with dry-coolers in hot climate). NOTE: to

ensure control of the condenser leaving water

temperature, this option must be fitted on the units.

30XWH- / XW-P /

XWHP 254-1762 &

30XW--0254/0304/354

Condensing temperature

limitation

150B Limitation of the maximum condenser leaving water temperature to

45°C

Reduced maximum power input and current absorption:

power cables and protection elements can therefore be

downsized

254-1762

Control for low cond.

temperature

152

Output signal (0-10 V) to control the condenser water inlet valve

Simple installation: for applications with cold water at

condenser inlet (ex. ground-source, groundwater-

source, superficial water-source applications) the signal

permits to control a 2 or 3-way valve to maintain

condenser water temperature (and so condensing

pressure) at acceptable values

254-1762

Energy Management Module

156

EMM Control board with additional inputs/outputs. See Energy

Management Module option chapter

Extended remote control capabilities (Set-point reset,

ice storage end, demand limits, boiler on/off

command...)

254-1762

7" user interface

158A Control supplied with a 7 inch colour touch screen user interface

Enhanced ease of use.

254-1762

Input contact for Refrigerant leak

detection

159

0-10 V signal to report any refrigerant leakage in the unit directly on

the controlller (the leak detector itself must be supplied by the

customer)

Immediate customer notification of refrigerant losses to

the atmosphere, allowing timely corrective actions

254-1762

Compliance with Swiss

regulations

197

Additional tests on the water heat exchangers: supply (additional

of PED documents) supplementary certificates and test

certifications

Conformance with Swiss regulations

254-1762

Compliance with Australian

regulations

200

Unit approved to Australian code

Conformance with Australian regulations

254-1762

Low noise level

257

Evaporator sound insulation

3 dB(A) quiter than standard unit

254-1762

Welded evaporator connection

kit

266

Victaulic piping connections with welded joints

Easy installation

254-1762

Welded condenser water

connection kit

267

Victaulic piping connections with welded joints

Easy installation

254-1762

Flanged evaporator water

connection kit

268

Victaulic piping connections with flanged joints

Easy installation

254-1762

Flanged condenser water

connection kit

269

Victaulic piping connections with flanged joints

Easy installation

254-1762

Thermal compressor insulation

271

The compressor is covered with a thermal insulation layer

Prevents air humidity to condensate on the compressor

surface

254-1762

230V electrical plug

284

230V AC power supply source provided with plug socket and

transformer (180 VA, 0,8 Amps)

Permits connection of a laptop or an electrical device

during unit commissioning or servicing

254-1762

Carrier Connect link (only

European distribution

companies)

298

3G router board NOTE 1: require option 149

NOTE 2: when more than one machine is installed on site, only

one of them shall be equipped with option 298 while all of them

must be equipped with option 149 NOTE 3: if the Carrier®

PlantCTRL™ is on site, option 298 shall be integrated in the

Carrier® PlantCTRL™ while option 149 is still mandatory for each

single unit.

Enabler for Carrier Connect service offer

254-1762

Summary of Contents for 30XW





































Search results

Summary of Contents for 30XW

Reviews:

Related manuals for 30XW

Brands by name

Popular brands

Carrier 30XW, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for 30XW

Reviews:

Related manuals for 30XW

Brands by name

Popular brands