Carrier 58SP0A Installation, Start-Up, Operating And Service And Maintenance Instructions Download

Page: 10 / 44

58SP0A/58SP1A: Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A96283

Fig. 10 – Floor and Plenum Opening Dimensions

A96285

Fig. 11 – Furnace, Plenum, and Subbase

Installed on a Combustible Floor

A08556

Fig. 12 – Furnace, Plenum, and Coil Assembly or

Coil Box Installed on a Combustible Floor

HORIZONTAL INSTALLATION

The furnace can be installed horizontally in an attic or crawlspace on

either the left-hand (LH) or right-hand (RH) side. The furnace can be

hung from floor joists, rafters or trusses or installed on a

non-combustible platform, blocks, bricks or pad.

Suspended Furnace Support

The furnace may be supported under each end with threaded rod, angle

iron or metal plumber’s strap as shown, see

Fig. 14

and

Fig. 15

. Secure

angle iron to bottom of furnace as shown. Heavy-gauge sheet metal

straps (plumber’s straps) may be used to suspend the furnace from each

bottom corner. To prevent screws from pulling out, use 2 #8 x 3/4 in.

screws into the side and 2 #8 x in. screws in the bottom of the furnace

casing for each strap, see

Fig. 14

and

Fig. 15

If the screws are attached to ONLY the furnace sides and not the bottom,

the straps must be vertical against the furnace sides and not pull away

from the furnace sides, so that the strap attachment screws are not in

tension (are loaded in shear) for reliable support.

Platform Furnace Support

Construct working platform at location where all required furnace

clearances are met, see

Fig. 2

and

Fig. 13

. For furnaces with 1-in. (25

mm) clearance requirement on side, set furnace on non-combustible

blocks, bricks or angle iron. For crawlspace installations, if the furnace

is not suspended from the floor joists, the ground underneath furnace

must be level and the furnace set on blocks or bricks.

A10164

Fig. 13 – Typical Attic Installation

A10130

Fig. 14 – Horizontal Unit Suspension

PLENUM

OPENING

FLOOR

OPENING

DOWNFLOW

SUBBASE

SHEET METAL

PLENUM

FLOOR

OPENING

FURNACE

(OR COIL CASING

WHEN USED)

COMBUSTIBLE

FLOORING

APPROVED

COIL ASSEMBLY

COIL BOX

FURNACE

SHEET METAL

PLENUM

FLOOR

OPENING

COMBUSTIBLE

FLOORING

30-IN. (762mm)
MIN WORK AREA

″

MIN

TYPE-B
VENT

″

SHEET
METAL

SEDIMENT

TRAP

EQUIPMENT MANUAL

SHUT-OFF GAS VALVE

LINE CONTACT ONLY PERMISSIBLE BETWEEN
LINES FORMED BY INTERSECTIONS OF
THE TOP AND TWO SIDES OF THE FURNACE
JACKET AND BUILDING JOISTS,
STUDS, OR FRAMING.

GAS
ENTRY

″

(451mm)OVERALL

″

(121mm) UNDER DOO

″

(25mm) UNDER FURNAC

EXTEND OUT 12

″

(305mm)

FROM FACE OF DOOR

* WHEN USED WITH
SINGLE WALL VENT
CONNECTIONS

UNION

(152mm)

(451mm)

(559mm)

" (6mm) THREADED ROD

4 REQ.

SECURE ANGLE
IRON TO BOTTOM
OF FURNACE WITH
3 #8 x

" (19mm) SCREWS

TYPICAL FOR 2 SUPPORTS

1” (25mm) SQUARE, 1-1/4”x1-1/4”x1/8” (32x32x3mm)
ANGLE IRON OR UNI-STRUT MAY BE USED

(2) HEX NUTS, (2) WASHERS & (2) LOCK WASHERS
REQ. PER ROD

8" (203mm)

MIN

FOR DOOR REMOVAL

OUTER DOOR
ASSEMBLY

Summary of Contents for 58SP0A













































Search results

Summary of Contents for 58SP0A

Reviews:

Related manuals for 58SP0A

Brands by name

Popular brands

Carrier 58SP0A, Installation, Start-Up, Operating And Service And Maintenance Instructions

Search results

Summary of Contents for 58SP0A

Reviews:

Related manuals for 58SP0A

Brands by name

Popular brands