background image

6

PERFORMING ROUTINE MAINTENANCE

With proper maintenance and care, your furnace will operate

economically and dependably. Instructions for basic maintenance
are found on this and the following pages. However, before

beginning maintenance, follow these safety precautions:

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal

injury or death.
Turn off electrical power supply to your furnace before

removing the access doors to service or perform

maintenance.

!

WARNING

CUT HAZARD

Failure to follow this caution may result in personal injury.
Although special care has been taken to minimize sharp

edges, be extremely careful when handling parts or reaching

into the furnace.

Wear safety glasses, gloves, and

appropriate protective clothing.

CAUTION

!

FILTERING OUT TROUBLE

UNIT PERFORMANCE HAZARD

Failure to follow this caution may result in product damage.
Never operate your furnace without a filter in place. Doing

so may damage the furnace blower motor.

An

accumulation of dust and lint on internal parts of your

furnace can cause a loss of efficiency.

CAUTION

!

A dirty filter will cause excessive stress on the furnace, heat

exchanger, and blower motor and can cause it to overheat and
automatically shut down. The furnace filter should be checked

every 4 weeks and cleaned or replaced if necessary.
If installed with factory specified disposable media filter, check or

replace filter before each heating and cooling season. Replace
disposable media filter at least twice a year.
If your furnace filter needs replacing, be sure to use the same size

and type of filter that was originally specified. The air filter for the
furnace may be located in a filter cabinet attached to the side or

bottom of the furnace. If air filter has been installed in another
location, contact your dealer for instructions. To inspect, clean

and/or replace the air filter(s), follow these steps:

1. Turn off the electrical supply to the furnace.

A92185

Fig. 13 -- Turn Off Electrical Supply

2. Remove filter cabinet door (See Fig. 14 and 15.)

NOTE

: It may be necessary to remove 1 thumbscrew.

A06190

Fig. 14 -- Removing Side Filter Cabinet Door

A06191

Fig. 15 -- Removing Bottom Filter Cabinet Door

3. Slide air filter out of filter cabinet. Keep dirty side up (if

dirty) to avoid spilling dirt. (See Fig. 16 and 17.)

Summary of Contents for Induced Combustion Gas Furnace











Reviews: