background image

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

47

A96316

Fig. 62 – Amp. Draw Check With Ammeter

b. Electronic thermostat: Set cycle rate for 4 cycles per hr.

9. Adjust Cooling Airflow. The  cooling airflow can be set from  the

remaining blower speed taps. Refer to the Air Delivery Tables in

these instructions.

10. Adjust  blower  off  delay.  The  blower  off  delay  has  four  (4)

adjustable settings from 90 seconds to 180 seconds. The blower off

delay jumpers are located on the furnace control board - see wiring

diagram  (see 

Fig. 67

).  Position  A-90  seconds,  B-120  seconds,

C-150 seconds, D-180 seconds.

To change the blower off delay setting, move the jumper from one

set of pins on the control to the pins used for the selected blower off

delay. Factory off delay setting is 120 seconds.

11. Cooling On Delay is fixed at 2 seconds for either jumper selection.

Check Safety Controls

1. Check Main Limit Switch(es)

This  control  shuts  off  combustion  control  system  and  energizes

air-circulating  blower  motor,  if  furnace  overheats.  By  using  this

method  to  check  limit  control,  it  can  be  established  that  limit  is

functioning  properly  and  will  operate if  there  is a  restricted  duct

system or motor failure. If limit control does not function during

this test, cause must be determined and corrected.

a. Run furnace for at least 5 minutes.

b. Gradually block off return air with a piece of cardboard or sheet 

metal until the limit trips.

c. Unblock return air to permit normal circulation for 5 minutes.

d. Main limit circuit open causes 3 hour lock out. 

e. Reset unit power to clear limit fault lockout.

Checklist

1. Put away tools and instruments. Clean up debris.
2. Verify that the Blower/Heat Off Delay jumpers are set as desired.

(see 

Fig. 41

 and 

Fig. 67

).

3. Verify that there are no unsealed openings in the blower shelf or

casing.

4. Verify that the blower (lower door in upflow position) and control

(“Main”  or  upper  door  in  upflow  position)  doors  are  properly

installed.

5. Verify  that  the  Status  LED  glows.  If  not,  check  that  the  power

supply  is  energized  and  that  the  blower  door  is  secure.  Interpret

diagnostic codes (see 

Fig. 63

).

6. Cycle test furnace with room thermostat to be sure that it operates

properly  with  the  room  thermostat.  Check  all  modes  including

Heat, Cool and Fan.

7. Check operation of accessories per manufacturer’s instructions.
8. Review Owner’s Manual with owner.
9. Attach entire literature packet to furnace.

R

Y W G

10 TURNS

THERMOSTAT SUBBASE
TERMINALS WITH
THERMOSTAT REMOVED
(ANITICIPATOR, CLOCK, ETC.,
MUST BE OUT OF CIRCUIT.)

HOOK-AROUND
AMMETER

EXAMPLE:

5.0 AMPS ON AMMETER
10 TURNS AROUND JAWS

 

=  

0.5 AMPS FOR THERMOSTAT

     ANTICIPATOR SETTING

FROM UNIT 24-V
CONTROL TERMINALS

Table 21 – Gas Rate (CU ft./hr)

SEC

FOR 1

REV 

SIZE OF TEST DIAL 

SEC

FOR 1

REV 

SIZE OF TEST DIAL 

1 Cu 

Ft. 

2 Cu 

Ft. 

5 Cu 

Ft. 

1 Cu 

Ft. 

2 Cu 

Ft. 

5 Cu 

Ft. 

10

360

720

1800

55

65

131

327

11

327

655

1636

56

64

129

321

12

300

600

1500

57

63

126

316

13

277

555

1385

58

62

124

310

14

257

514

1286

59

61

122

305

15

240

480

1200

60

60

120

300

16

225

450

1125

62

58

116

290

17

212

424

1059

64

56

112

281

18

200

400

1000

66

54

109

273

19

189

379

947

68

53

106

265

20

180

360

900

70

51

103

257

21

171

343

857

72

50

100

250

22

164

327

818

74

48

97

243

23

157

313

783

76

47

95

237

24

150

300

750

78

46

92

231

25

144

288

720

80

45

90

225

26

138

277

692

82

44

88

220

27

133

267

667

84

43

86

214

28

129

257

643

86

42

84

209

29

124

248

621

88

41

82

205

30

120

240

600

90

40

80

200

31

116

232

581

92

39

78

196

32

113

225

563

94

38

76

192

33

109

218

545

96

38

75

188

34

106

212

529

98

37

74

184

35

103

206

514

100

36

72

180

36

100

200

500

102

35

71

178

37

97

195

486

104

35

69

173

38

95

189

474

106

34

68

170

39

92

185

462

108

33

67

167

40

90

180

450

110

33

65

164

41

88

176

439

112

32

64

161

42

86

172

429

116

31

62

155

43

84

167

419

120

30

60

150

44

82

164

409

124

29

58

145

45

80

160

400

129

28

56

140

46

78

157

391

133

27

54

135

47

76

153

383

138

26

52

130

48

75

150

375

144

25

50

125

49

73

147

367

150

24

48

120

50

72

144

360

157

23

46

115

51

71

141

355

164

22

44

110

52

69

138

346

171

21

42

105

53

68

136

340

180

20

40

100

54

67

133

333

 

 

 

 

Summary of Contents for PG95ESU



























































Reviews: