Carrier PG95ESU User Manual Download

Page: 17 / 58

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A190301

Fig. 26 – Dimensions of 8-in. Tall Metal Spacer

NOTE:

The allowable use of the 8-in. spacer demonstration (

Table 6

and

Fig. 26

). The spacer may taper to accommodate different

coil/furnace width combinations but must always keep an 8-in.

minimum height if used. Space between the top of the furnace casing

and the bottom of the coil.

NOTE:

When the indoor coil is placed in an unconditioned space,

insulation should be applied and wrapped around the outside of coil

casing, 8-in. adapter and supply duct contact point.

1. Create field fabricated adapter (if needed,

Table 6

2. If adapter is needed, place field fabricated adapter on furnace.

Adapter should be tapered to fit coil/furnace combination when one

of them is larger than the other.

3. Set coil on adapter.
4. Ensure coil is level for proper condensate drainage. In upflow

application, do not tip coil toward condensate drain. In the

horizontal application, ensure coil cabinet is level side to side and

front to back. It is allowable to add up to 1/2-in additional slope

over length and depth of coil cabinet in the direction of drain pan

connection.

5. Attach coil casing to furnace using sheet metal screws. If 8-in.

spacer is required, attach coil casing to spacer and attach spacer to

furnace using sheet metal screws.

6. Seal joints between coil casing, adapter (if needed,

Table 6

), and

furnace to create an air tight seal using locally approved materials.

Upflow Installation

NOTE:

The furnace must be pitched for proper condensate drainage

(see

Fig. 31

Supply Air Connections

For a furnace not equipped with a cooling coil, the outlet duct shall be

provided with a removable access panel. This opening shall be

accessible when the furnace is installed and shall be of such a size that

the heat exchanger can be viewed for possible openings using light

assistance or a probe can be inserted for sampling the air stream. The

cover attachment shall prevent leaks.

Connect supply-air duct to flanges on furnace supply-air outlet. Bend

flange upward to 90° with wide duct pliers (see

Fig. 27

). The supply-air

duct must be connected to ONLY the furnace supply-outlet-air duct

flanges or air conditioning coil casing (when used). DO NOT cut main

furnace casing side to attach supply air duct, humidifier, or other

accessories. All supply-side accessories MUST be connected to duct

external to furnace main casing.

A190216

Fig. 27 – Duct Flanges

NOTE:

Coil offset kits do not meet the 8-in. separation between the coil

pan and furnace if required (

Table 6

). Additional metal shield or an

extension to achieve an 8-in. total separation is required.

Return Air Connections

The return-air duct must be connected to bottom, sides (left or right), or a

combination of bottom and side(s) of main furnace casing. Bypass

humidifier may be attached into unused return air side of the furnace

casing (see

Fig. 28

and

Fig. 29

Cabinet Size

Dimension “B”

17-in.

17-1/2-in.

21-in.

esentative d

awing only, some models may va

Coil Spacer

nace

Coil

nace

20---1/2”

”

WARNING

FIRE HAZARD

A failure to follow this warning could cause personal injury, death

and/or property damage.

Never connect return-air ducts to the back of the furnace. Follow

instructions below.

UPFLOW

HORIZONTAL

YES

120

MIN

YES

120

MIN

YES

PERFORATED
DISCHARGE DUCT
FLANGE

Summary of Contents for PG95ESU



























































Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands

Carrier PG95ESU, User Manual

Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands