Carrier PG95ESU User Manual Download

Page: 46 / 58

PG95ESU: Installation, Start-up, Operating and Service Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

5. Verify natural gas input rate by clocking meter.

NOTE:

Gas valve regulator adjustment cap must be in place for proper

input to be clocked.

a. Turn off all other gas appliances and pilots served by the meter.

b. Jumper R and W thermostat connections at the furnace control

board.

c. Run furnace for 15 minutes in heating operation.

d. Measure time (in seconds) for gas meter to complete 1 revolution

and note reading. The 2 or 5 cubic feet dial provides a more

accurate measurement of gas flow.

e. For cubic ft. of gas per hr (

Table 21

f. Multiply gas rate (cu ft./hr) by heating value (BTUh/cu ft.) to

obtain input.

If clocked rate does not match required input from Step 1, increase gas

valve outlet pressure to increase input or decrease gas valve outlet

pressure to decrease input. Repeat steps b through e until correct input is

achieved. Reinstall regulator seal cap on gas valve.

6. Restore furnace to normal operating condition.

a. When correct input rate and temperature rise is achieved, turn

gas valve ON/OFF switch to OFF.

b. Remove manometer or similar device from gas valve.

Tighten set scr

ew on outlet tower

pressure tap with 3/32 in. hex

wrench.

d. Turn gas valve ON/OFF switch to ON.

e. Check for gas leaks and verify furnace operation.

7. Set temperature rise. The furnace must operate within the

temperature rise ranges specified on the furnace rating plate.

Determine the temperature rise as follows:

NOTE:

Blower access door must be installed when taking temperature

rise reading. Leaving blower access door off will result in incorrect

temperature measurements.

a. Place thermometers in return and supply ducts as close to furnace

as possible. Be sure thermometers do not see radiant heat from

heat exchangers. Radiant heat affects temperature rise readings.

This practice is particularly important with straight-run ducts.

b. When thermometer readings stabilize, subtract return-air

temperature from supply-air temperature to determine air

temperature rise.

NOTE:

If the temperature rise is outside this range, first check:

(1.) Gas input for heating operation.

(2.) Return and supply ducts for excessive restrictions causing

static pressures greater than the maximum heating static

listed on the rating plate.

c. Adjust air temperature rise by adjusting blower speed. Increase

blower speed to reduce temperature rise. Decrease blower speed

to increase temperature rise

d. Turn thermostat down below room temperature and remove

blower access door.

e. To change motor speed selection for heating, remove blower

motor lead from control HEAT terminal - Wiring Diagram (see

Fig. 67

) Select desired blower motor speed lead from one of the

other terminals and relocate it to the HEAT terminal - lead color

identification (

Table 11

). Reconnect original lead to SPARE

terminal.

f. Repeat steps a through e.

8. Set thermostat heat anticipator.

a. Mechanical thermostat - Set thermostat heat anticipator to match

the amp. draw of the electrical components in the R-W circuit.

Accurate amp. draw readings can be obtained at the wires

normally connected to thermostat subbase terminals, R and W.

The thermostat anticipator should NOT be in the circuit while

measuring current.

A180238

Fig. 61 – Orifice Hole

(1.) Remove thermostat from subbase or from wall.

(2.) Connect an amp. meter (see

Fig. 62

) across the R and W

subbase terminals or R and W wires at wall.

(3.) Record amp. draw across terminals when furnace is in

heating and after blower starts.

(4.) Set heat anticipator on thermostat per thermostat

instructions and install on subbase or wall.

CAUTION

FURNACE DAMAGE HAZARD

Failure to follow this caution may result in:

Overheating the heat exchangers or condensing flue gases in

heat exchanger areas not designed for condensate.

Shortened furnace life

Component damage

Temperature rise must be within limits specified on furnace rating plate.

Recommended operation is at midpoint of rise range or slightly above.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury or death.

Disconnect 115-v electrical power and install lockout tag before

changing speed tap.

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death,

and/or property damage.

Gas valve outlet pressure tap must be tightened to prevent gas leak.

CAUTION

FURNACE OVERHEATING HAZARD

Failure to follow this caution may result in reduced furnace life.
Recheck temperature rise. It must be within limits specified on the

rating plate. Recommended operation is at the mid-point of rise range

or slightly above.

BURNER

ORIFICE

Summary of Contents for PG95ESU



























































Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands

Carrier PG95ESU, User Manual

Search results

Summary of Contents for PG95ESU

Reviews:

Related manuals for PG95ESU

Brands by name

Popular brands